|
|
Professional-grade Soda/Abrasive Blaster converts between m
... Read more
Professional-grade Soda/Abrasive Blaster converts between media in minutes to remove paint and rust safely...strips without chemicalsThis USA-made, 2-in-1 soda blaster is the smart choice for the professional refinisher for removing paint and rust without harming sheet metal, glass, or chrome...converts in minutes to abrasives when your project needs more aggressive blasting.10' blast hose with heavy-duty deadman valve gives you optimal control50-lb.-capacity, all-steel, welded hopper has a concave top for easy fillingIncludes pressure gauge requires as little as 10 cfm at 90 psiIncludes 3/32 ceramic nozzleMade in USAUSA-made 2-in-1 blaster workswith as little as 10 cfm at 90 psi Soda blasting removes paint without harming sheet metal, glass, or chrome, and while our competitors' commercial soda blasters use high air volume, this pro-grade Eastwood soda blaster requires just 10 cfm at 90 psi. This soda blaster provides a big 50-lb. capacity and includes a lengthy 10'-long, 1/2-I.D. blast hose with heavy-duty deadman valve all-steel welded, top-loading hopper pressure gauge. Includes 3/32 ceramic nozzle. Rolls easily to job site on two wheels. Readily converts between soda and aggressive abrasive blasting with included parts. Made in USA.More Uses for Bicarbonate Soda (Baking Soda) BlastersYou can also use bicarbonate soda blast media (NOT household baking soda) to remove graffiti and grime from brick, concrete, limestone, granite and other surfaces. Other uses included cleaning of delicate substrates, architectural and industrial cleaning, paint stripping, corrosion removal. Use to remove mold and mildew stains from pools, cement, brick, tile, granite, sound stucco, siding and more. Safely strip paint from aircraft aluminum, trucks, motorcycles. Bicarbonate soda also allows heavy-duty removal of oils and grease from engines and floors.Simple bolt-together assembly will have you blasting in about 45 minutes. Approximately 36 high with handles, and about 24 in diameter, so it will easily store in the corner of your shop or garage.Click Here to learn more about soda blasting. 50-lb.-capacity soda blaster comes complete, except for your compressor and air-fitting coupler to match your air lines. Includes 3/32 ceramic nozzle. 22012 3/32 Ceramic Nozzle11806 Automotive (Medium) Bicarbonate Soda Media11807 Automotive (XL) Bicarbonate Soda Media50494 Rust Remover Bicarbonate Soda with 20 Aluminum Oxide50417 Galvanized Abrasive Media Funnel Strainer 50097 Soda-Blasting Protection Kit (Q) Why use bicarbonate soda media(A) Soda will not harm glass, plastics, fiberglass or chrome surfaces. It's used to remove paint coatings from the vehicle surface without etching the surface or warping the metal like more aggressive media would. It's the best way to strip fiberglass Corvettes, boats or aftermarket hoods. Also used to remove paint from urethane and SMC-type bumper fascias. (Q) Can this unit be used with more aggressive media(A) Yes, this unit can be converted to blast standard abrasive medias such as crushed glass, aluminum oxide, etc. by using the abrasive kit included. Bicarbonate soda blasting is much safer than traditional abrasives, and more gentle to the metal or substrate you're blasting. However, you must still protect yourself from the dust and, more importantly, the particles of paint, corrosion or scale that become airborne during the blasting operation.Use a properly fitted dust mask or respirator, safety glass or safety shield, plus heavy gloves, long pants and a long-sleeve shirt to protect exposed skin. Use our 50097 Soda-Blasting Protection Kit for complete protection.Make sure you disconnect the air line and allow the tank to bleed pressure before opening the fill cap.Do not aim the nozzle anywhere other than the substrate you are blasting.Check the condition of the nozzle after every hour of blasting and replace once wear is visible or the blast stream becomes ineffective.Before each use, inspect the tank for any si
Minimize
|
This store is not yet rated
|
Go To Store
|
|
|
Lenox 30864 Specifications: Diameter: 6-7/8"Lenox 30864 F
... Read more
Lenox 30864 Specifications: Diameter: 6-7/8"Lenox 30864 Features: Applications: Fixtures For Fixtures: Capri Hubbell Lightolier Lithonia Marco Prescolite ProgressSmooth fast cutting -high abrasive resistance -no snagging or binding -cuts in both directions -tungsten carbide continuous edge -grit hardness Ra 90-93Uses 2L arbors 1-5/8" cutting depth -cuts material that bi-metal will not: plaster drywall acoustic tile ceiling tile stucco with wire mesh support plaster with lathAdd On Item Number 123CT Carbide Tipped Pilot Pin For Easy Cutting
Minimize
|
|
Go To Store
|
|
|
|
|
from $171
(11 stores)
See Details
|
|
|
|
|
from $165
(8 stores)
See Details
|
|
|
AGL LS-100 Detector and Rod ClampAGL LS-100 Detector is a f
... Read more
AGL LS-100 Detector and Rod ClampAGL LS-100 Detector is a full featured receiver with proven performance in the field. Three bright LED s, nine channel arrow display and audio output provide the user with all the information needed to lock on the laser beam and get the job done right.Features:Three bright LED s can be used as a reference for the receiver s positionNine channel arrow display provides a stepped reference as you approach the laser beamAudio outputDouble deep beam finderLast beam strike memoryLow battery indicationReversible clamp ensures solid mounting to both rectangular or oval rodsDetects and ignores the flash from strong strobes on the jobAllows you to work with a fine, medium or coarse band widthEstablished in 1992, Agatec is a European specialist in laser tools that serves enterprises with innovative technology and solutions for every construction site. Since the early nineties the company works closely with customers, observing the dynamic of their job and delivering tools that make working easier, improving productivity and reducing costs.
Minimize
|
This store is not yet rated
|
FREE Shipping
Go To Store
|
|
|
|
|
from $121
(2 stores)
See Details
|
|
|
Hurry This item ships FREE for a limited time.Save BIG mon
... Read more
Hurry This item ships FREE for a limited time.Save BIG money when you get our TIG 200 Welder PLUS our Versa-Cut Plasma Cutter, and organize it all on the Cart includedClick on the individual links below for all the specs, but you must click the Buy Now button below to get the special savings over individual pricesEastwood-engineered TIG 200 AC/DC Welder offers professional-quality TIG welding at an affordable priceOperates on either 110vAC, 15-amp circuit or 220vAC, 30-amp circuit1/4-thick welding capacityHigh-frequency start for precise arc controlSquare-wave inverter for accurate aluminum weldingThe Eastwood Versa Cut Plasma Cutter works with either 110v or 220v input to easily slice through steel and non-ferrous metals up to 3/8 thick.110v or 220v AC input with inverter technology20' torch cable 10' ground cable with clampRated 40-amp outputNow with a black powder-coat finishOur Multi-Unit Welding Cart is designed specifically to keep all your Eastwood welding and cutting equipment and accessories organized.Top shelf holds the TIG-200 welder (or either of our MIG welders)Bottom shelf holds the Versa-Cut Plasma CutterMiddle shelf is for accessory storageGas-bottle mount includes a TIG rod holder Click here for welder warranty informationLimited Time OfferHot Deal FREE SHIPPING TIG200 WelderWeld it all with the Eastwood TIG200 200AMP welder The TIG200 features an AC/DC switch that allows both steels and aluminum to be welded with the same machine. With a 14' torch and a 10' ground cable, you'll be able to get into any space with this exceptional machine. It has pre/post flow adjustment knobs to protect your weld and torch. If that's not enough, it even has a foot pedal to control amperage so you can get going quickly and not need to dial-in the machine for a specific material. Included is the TIG200, torch, ground cable/clamp, regulator/hose, and is powered through a NEMA50 plug.Plasma CutterThis innovative, affordable, plasma cutter was designed and developed by Eastwood's own RD staff, and tested in-house on the same type of real-life projects you'll use it for. It doesn't matter where you need to work, because this plasma cutter's voltage-sensing technology lets you use either a 110v or 220v outlet with our adapter cord. Works with any standard home- or shop-type air compressor within a range of 20-65 psi internal moisture separator ensures dry air is delivered to the torch. Rated 140 volts at 40 amps. Duty cycle 60 at 40 amps. Weighs less than 30 lbs., for easier portability.Multi-Unit CartThis welding cart was designed by to make storage, accessibility and maneuverability of your welder and cutter easier than ever before. This cart incorporates a top shelf which will hold our MIG135, MIG175 or TIG-200 welder. The bottom shelf will store your Versa-Cut Plasma Cutter, while the middle shelf allows storage of necessary welding accessories. The Gas Bottle Mount even incorporates a TIG Rod Holder to store up to 6 different tubes of filler rods. Assembles with simple hand tools.What is Plasma Cutting Plasma cutting utilizes a high-velocity jet of ionized gas (plasma) that conducts electricity from the torch of the plasma cutter to your metal workpiece. That directed plasma stream (about 30,000deg F) heats the workpiece, converting the metal to molten slag. That high-velocity stream literally blows the molten metal away, leaving a clean, precise cut. TIG200 UnitShielding Gas RegulatorShielding Gas HoseGround Cable with Clamp (10ft)TIG Torch (17 Series) which accepts industry standard cups, collets, and collet bodies (14 ft.)Foot Pedal for Amperage Control110v-to-200v Adapter PlugManualHand Held ShieldHammer/Brush7 Cup (7/16), 6 Cup (3/8), 5 Cup (5/16)Long Back Cap, Short Back Cap3/32 Collet Body, 3/32 Collet, 1/16 Collet, 2.0mm Collet2.0mm Red (Thoriated Tungsten)Versa-Cut Plasma CutterTorch AssemblyGround Clamp Assembly110/220v Adapter CordWelding CartAssembly Instructions Input voltage single phase 110 or 220 VAC (+/- 15)
Minimize
|
This store is not yet rated
|
FREE Shipping
Go To Store
|
|
|
Shop for Lighting & Fans at The Home Depot. The Westinghous
... Read more
Shop for Lighting & Fans at The Home Depot. The Westinghouse 14-Piece Lighting Fixture Repair Kit offers a quick, safe way to repair your worn-out lamps. The kit includes two 5/32 x 15mm holder screws, two 5/32 x 12mm holder screws, two 5/32 x 5/8 in. screws, two 5/32 x 3/8 in. screws, two 8/32 x 1 in. crossbar screws and 4 knurled knobs.
Minimize
Up to 70% Off Select Lighting. Online Only at homedepot.com.
In stock
|
|
Go To Store
|
|
|
Save BIG money when you get our MIG 135 Welder PLUS our Ver
... Read more
Save BIG money when you get our MIG 135 Welder PLUS our Versa-Cut Plasma CutterClick on the individual links below for all the specs, but you must click the Buy Now button below to get the special savings over individual pricesEastwood's own MIG 135 Welder works as well as the name brands, but at a fraction of the price It produces excellent bead quality and capabilities that matchand even exceedthe more expensive competitionWelds mild and stainless steel, 24-ga. to 1/425-135-amp welding rangePowered by standard 120v household currentThe Eastwood Versa Cut Plasma Cutter works with either 110v or 220v input to easily slice through steel and non-ferrous metals up to 3/8 thick.110v or 220v AC input with inverter technology20' torch cable 10' ground cable with clampRated 40-amp outputNow with a black powder-coat finishClick here for welder warranty informationSave when you buy them as a setfor all your welding and cutting jobs MIG 135 welder is designed for the home hobbyist and light fabricator. Welder comes complete (except for the gas cylinder) and ready to weld 24-gauge to 1/4 mild steel and stainless. Welder has a 20 duty cycle at 90 amps, and 25-135-amp welding range. Feeds wire at 39-468 per minute, and has infinitely adjustable wire speed and heat settings. Includes a precision-drive motor, regulator with hose, wire, tips and accessories...just add your own cylinder of CO2/Argon. Quick Set weld chart specifies settings for each material thickness, eliminating guesswork and assuring complete penetration. Backed by Eastwood's no-hassle return policy and a 3-year manufacturer's warranty. Plasma CutterThis innovative, affordable, plasma cutter was designed and developed by Eastwood's own RD staff, and tested in-house on the same type of real-life projects you'll use it for. It doesn't matter where you need to work, because this plasma cutter's voltage-sensing technology lets you use either a 110v or 220v outlet with our adapter cord. Works with any standard home- or shop-type air compressor within a range of 20-65 psi internal moisture separator ensures dry air is delivered to the torch. Rated 140 volts at 40 amps. Duty cycle 60 at 40 amps. Weighs less than 30 lbs., for easier portability.What is Plasma Cutting Plasma cutting utilizes a high-velocity jet of ionized gas (plasma) that conducts electricity from the torch of the plasma cutter to your metal workpiece. That directed plasma stream (about 30,000 degrees F) heats the workpiece, converting the metal to molten slag. That high-velocity stream literally blows the molten metal away, leaving a clean, precise cut. MIG 135 Welder (57 lbs.) 0.023 Steel MIG Wire Extra 0.023 Contact TipGas Regulator with hoseTweco-Style Gun and Consumables Switchable Drive Roller8' Ground Cable and Gun Cable Wire BrushWelding Face Shield Plasma CutterIncludes Versa Cut unit, torch assembly, ground clamp assembly, 110/220V adapter cord. MIG 13512211-Contact Tip 0.02312224-Contact Tip 0.030 12226-MIG Wire 0.02312227-MIG Wire 0.03012225-Flux Wire 0.03012239-Drive Roller12238-Gas Regulator12210-Tweco-Style NozzlePlasma Cutter12814 Versa-Cut Nozzles, 10 pcs.12812 Versa-Cut Electrodes, 10 pcs.Consumable parts can be purchased through Eastwood or are available at most local welding supply stores. If buying locally ask for the followingNozzle Brand Hypertherm, Part Number 020115Electrode Brand Hypertherm, Part Number 020167 MIG 135Click here for product instructionsWelding steel, stainless metals this unit welds 20- and 18-gauge body panels beautifully. The amperage and output voltage can be controlled precisely to get the proper penetration required. The wire speed can be infinitely adjusted also to gain proper wire fill in the weld pool. This unit has been compared to the leading U.S.-manufactured red welders with equal results at a fraction of the cost. The drive roll mechanism, the heart of any MIG welder, is designed to our specifications and delivers flawless wire feed without skipping or slip
Minimize
|
This store is not yet rated
|
Go To Store
|
|
|
Underground Enclosure Assembly, Pg, Cover Logo Lighting, No
... Read more
Underground Enclosure Assembly, Pg, Cover Logo Lighting, Nominal Length 21 1/4 In., Nominal Width 11 3/4 In., Nominal Height 10 In., Cover Bolt Type 2 Stainless Steel Hex Head Bolts 3/8-16 X 2 3/4, Cover Pull Slot Size 1/2 X 4 In, Color Gray, Material Of Construction Monolithic Polymer Concrete, Description/special Features Stackable, Open Bottom Box W/ Cover, Non-deliberate Traffic Only, Load Rating 8000 Lbs., Standards Ul Listed To Ansi/scte 77 2007 Tier 8
Minimize
|
|
Go To Store
|
|
|
|
|
from $253
(6 stores)
See Details
|
|
|
Also known as: LIN3601, LNC3601, LNI-3601, LNL-3601; Featur
... Read more
Also known as: LIN3601, LNC3601, LNI-3601, LNL-3601; Features and Benefits All steel design includes reinforced caster supports for durability and dependability 18 gallon tank includes a preset air regulator that allows the use of standard shop air up to 150 PSI 14" telescoping bowl with a height adjustment range of 45" to 72" Reinforced dispensing hose doubles as a sight gauge to prevent overfilling Includes safety valveDesigned to provide a safe, affordable option for draining, transferring and evacuating motor oils, as well as transmission and power steering fluids quickly. It offers excellent mobility, easy bowl positioning and simple-to-use pressurized evacuation. Weight: 66 lbs.
Minimize
|
|
FREE Shipping
Go To Store
|
|
|
Save BIG money when you get our TIG 200 Welder PLUS our Ver
... Read more
Save BIG money when you get our TIG 200 Welder PLUS our Versa-Cut Plasma CutterClick on the individual links below for all the specs, but you must click the Buy Now button below to get the special savings over individual pricesEastwood-engineered TIG 200 AC/DC Welder offers professional-quality TIG welding at an affordable priceOperates on either 110vAC, 15-amp circuit or 220vAC, 30-amp circuit1/4-thick welding capacityHigh-frequency start for precise arc controlSquare-wave inverter for accurate aluminum weldingThe Eastwood Versa Cut Plasma Cutter works with either 110v or 220v input to easily slice through steel and non-ferrous metals up to 3/8 thick.110v or 220v AC input with inverter technology20' torch cable 10' ground cable with clampRated 40-amp outputNow with a black powder-coat finishClick here for welder warranty informationSave when you buy them as a setfor TIG welding and cutting jobs Weld it all with the Eastwood TIG200 200AMP welder The TIG200 features anAC/DC switch that allows both steels and aluminum to be welded with the samemachine. With a 14' torch and a 10' ground cable, you'll be able to get intoany space with this exceptional machine. It has pre/post flow adjustment knobsto protect your weld and torch. If that's not enough it even has a foot pedalto control amperage so you can get going quick and not need to dial in themachine for a specific material. Included is the TIG200, torch, groundcable/clamp, regulator/hose, and is powered through a NEMA50 plug.Plasma CutterThis innovative, affordable, plasma cutter was designed and developed by Eastwood's own RD staff, and tested in-house on the same type of real-life projects you'll use it for. It doesn't matter where you need to work, because this plasma cutter's voltage-sensing technology lets you use either a 110v or 220v outlet with our adapter cord. Works with any standard home- or shop-type air compressor within a range of 20-65 psi internal moisture separator ensures dry air is delivered to the torch. Rated 140 volts at 40 amps. Duty cycle 60 at 40 amps. Weighs less than 30 lbs., for easier portability.What is Plasma Cutting Plasma cutting utilizes a high-velocity jet of ionized gas (plasma) that conducts electricity from the torch of the plasma cutter to your metal workpiece. That directed plasma stream (about 30,000 degrees F) heats the workpiece, converting the metal to molten slag. That high-velocity stream literally blows the molten metal away, leaving a clean, precise cut. TIG200 UnitShielding Gas RegulatorShielding Gas HoseGround Cable with Clamp (10ft) TIG Torch (17 Series) which accepts industry standard cups, collets, and collet bodies (14ft) Foot Pedal for Amperage Control110v to 200v Adapter PlugManualHand Held ShieldHammer/Brush7 Cup (7/16),6 Cup (3/8),5 Cup (5/16) Long Back Cap,Short Back Cap3/32 Collet Body,3/32 Collet,1/16 Collet,2.0mm Collet2.0mm Red (Thoriated Tungsten)Plasma CutterIncludes Versa Cut unit, torch assembly, ground clamp assembly, 110/220V adapter cord. Input voltage single phase 110 or 220 VAC (+/- 15) 50-60HzInput amperage 28 ampOutput amperage 10-200amp AC/DCNo-load voltage 51AC duty cycle () 20-80 (80 at 100 amp- 20 at 200 amp) Pulse duty cycle () 10-90Post gas flow 2-8 secPre gas flow 0.1-1 secRemote foot pedal and control yesEfficiency () 80Weight 44lbsThe cleaning/clearance effect (AC balance control) of our unit is adjustable to provide wider cleaning with shallow penetration to narrow cleaning with deeper penetration. Changing electrode from EN (electrode negative) to EP (electrode positive)The frequency is fixed at 60Hz which provides a little wider bead but with good penetration for aluminum and magnesium. Our Tig 200 is constructed with inverter and MOSFET technology for optimum performance at a very affordable price.AccesoriesTIG Welding CartAuto Darkening Welding HelmetWelding JacketLarge View Auto Darkening HelmetWelding GlovesConsumables1/6 Inch Collet Body3/32 Inch Collet BodyTIG Torch Rear Back Cap3/8
Minimize
|
This store is not yet rated
|
Go To Store
|
|
|
|
|
from $160
(2 stores)
See Details
|
|
|
Our best value HotCoat Powder-Coating Starter Kit includes
... Read more
Our best value HotCoat Powder-Coating Starter Kit includes our Dual-Voltage gun for greater versatilityWith our dual-voltage HotCoat gun, you can powder coat interiors and hard-to-reach corners using the low 15,000-volt setting, or switch to the high 25,000-volt setting for multi-coat coverage over larger areas with increased powder adhesion and minimal overspray. Either way, you'll get all the benefits of powder coating in your own shop Besides the dual-voltage gun, this kit also includes gloss black color, plus everything else you'll need (except compressed air and a dedicated oven) to achieve expert results.Extremely durable finishCoat and cure in under an hourEasy to applyQuick color changesEconomical Kit includes our Dual-VoltageGun, gloss black powder and more Power unit supplies over 9000 VDC at 15 micro amps. Plugs into grounded 110- 20VAC outlet. Gun requires as little as.5 cfm at 5-10 psi. Fill cup no more than 1/4-1/3 full, wave the nozzle in a circular motion about 4-6 from the surface to keep the powder flowing efficiently and coat evenly. Use 8 psi for best results. Powder coated surfaces withstand fuel, Brake fluids and most solvents and are very chip resistant. Wear a dust mask when handling or applying powder. Wear a respirator while curing powder. Do not apply powder into a small boxed area.Why powder coat Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections. One 8-oz. bottle of powder covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the over-sprayed powder. Contains no environmentally harmful solvents. HotCoat Powder Coating System requires a 5-10psi compressed air source and dedicated electric oven (or toaster oven). (See Contents tab for all the specific items included in this Dual-Voltage kit.) 11676 Eastwood Dual-Voltage HotCoat Gun 1/2-lb. Black Gloss Powder51558 Powder Chip Color Chart10078 Reusable Hi-Temp Silicone Plugs 10027 Hi-Temp Masking Tape (1/2 x 36-yard roll)43045 1-lb. Stainless Steel Hanging Wire34128 Fluidizing Attachment34066 In-Line Air Filter3 Empty Powder Bottles with Screw-On Tops Accessories10041Z PRE Painting Prep51081 Metal Wash Metal Prep19418ZP Fast Etch Rust Remover and Metal Prep20473 2-Stage Air Dryer System58111 Pack of 20 Hooks58112 Silicone Cap Plug Kit11477 Infrared Thermometer10590 Infrared Curing Lamp (Q) Can I use my household oven(A) No, you cannot use an oven that will be used to cook/bake food. (Q) How long do I bake/cure the part (A) 20 minutes at 400 degreesF.(Q) Can I remove the powder coating(A) Yes, use 12849 Powder Coat Paint Dissolver (Qt.) or 12850 Powder Coat Paint Dissolver (Gal.).(Q) How do I know what the colors will look like(A) Order Eastwood's 51558 HotCoat Powder Coating Chip Chart (free in our kits). Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep updo not vacuumpowder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh cartridges when curing or inspecting flow-out progress. 1-year mfr's. warranty against defects.Designed, engineered and tested to Eastwood's specifications.Final product imported. 11698 58100 10198 DUAL-VOLTAG
Minimize
|
This store is not yet rated
|
FREE Shipping
Go To Store
|
|
|
Versa-Cut Plasma Cutter easily slices through materials up
... Read more
Versa-Cut Plasma Cutter easily slices through materials up to 3/8 thick...works anywhere with a 110v or 220v outletOur Eastwood-designed plasma cutter is your smartest choice for making clean, fast cuts through steel, stainless or aluminum as thin as 24-gauge, or as thick as 3/8. Compared to mechanical cutting, our Versa-Cut Plasma Cutter works significantly faster, and makes curved and intricate cuts more easily and precisely. Inverter technology offers superior arc stability and cutting power using either 110 or 220 volts. 110v or 220v AC input with inverter technology20' torch cable 10' ground cable with clampRated 40-amp output Air flow rate 3.0cfm at 20-65psiBacked by Eastwood's no-hassle 3-year warrantyGet this Plasma Cutter PLUS our MIG 175 Welder and SAVE BIGClick here to see our money-saving Versa Cut Plasma Cutter and MIG175 KitGet this Plasma Cutter PLUS our MIG 135 Welder and SAVE BIGClick here to see our money-saving Versa Cut Plasma Cutter and MIG135 KitGet this Plasma Cutter PLUS our TIG 200 Welder and SAVE BIGClick here to see our money-saving Versa Cut Plasma Cutter and TIG 200 Welder KitThis unit now comes with a black powder-coated finish.Clean, fast cuts thru steel, stainless,aluminum from 24-ga. to 3/8 This innovative, affordable, plasma cutter was designed and developed by Eastwood's own RD staff, and tested in-house on the same type of real-life projects you'll use it for. It doesn't matter where you need to work, because this plasma cutter's voltage-sensing technology lets you use either a 110v or 220v outlet with our adapter cord. Works with any standard home- or shop-type air compressor within a range of 20-65 psi internal moisture separator ensures dry air is delivered to the torch. Rated 140 volts at 40 amps. Duty cycle 60 at 40 amps. Weighs less than 30 lbs., for easier portability.What is Plasma Cutting Plasma cutting utilizes a high-velocity jet of ionized gas (plasma) that conducts electricity from the torch of the plasma cutter to your metal workpiece. That directed plasma stream (about 30,000 degrees F) heats the workpiece, converting the metal to molten slag. That high-velocity stream literally blows the molten metal away, leaving a clean, precise cut. Includes Versa Cut unit, torch assembly, ground clamp assembly, 110/220V adapter cord. Parts Consumables12814 Versa-Cut Nozzles, 10 pcs.12812 Versa-Cut Electrodes, 10 pcs.Consumable parts can be purchased through Eastwood or are available at most local welding supply stores. If buying locally, ask for the followingNozzle Brand Hypertherm, Part Number 020115Electrode Brand Hypertherm, Part Number 020167 Always wear approved eye protection and gloves. Do not use around flammable materials. Do not open machine. There are no user-serviceable parts. Click here for warranty 12740 CUT40 FS12740 FS12740D VERSA-CUT VERSA CUT VERSACUT CUTTING CUT METAL
Minimize
|
This store is not yet rated
|
Go To Store
|
|
|
Underground Enclosure Cover, Pc, Cover Logo Lighting, Cover
... Read more
Underground Enclosure Cover, Pc, Cover Logo Lighting, Cover Bolt Type 2 Stainless Steel Hex Head Bolts 3/8-16 X 1 1/2, Cover Pull Slot Size 1/2 X 2 In, Length 12 13/16 In, Width 12 13/16 In, Depth 3/4 In, Color Gray, Material Of Construction Monolithic Polymer Concrete, For Use With 14 3/4x14 3/4 Enclosures, Load Rating 8,000 Lbs., Description/special Features For Areas With Non-deliberate Traffic Only, Standards Ul Listed To Ansi/scte 77 2007 Tier 8
Minimize
|
|
Go To Store
|
|
|
Reed OLBUCKT1 Specifications: Weight: 21 lbs. Reed OLBUC
... Read more
Reed OLBUCKT1 Specifications: Weight: 21 lbs. Reed OLBUCKT1 Includes: (1) Oiler Bucket with Gun Reed Oilers effectively deliver threading oil to piping work. The gun-and-trigger approach makes it easy to pump oil directly on the work. The rugged and completely portable Reed OLBUCKT1 (#06150) comes with both a metal bucket and a metal drip pan/chip tray (#97375 drip pan/chip tray is available separately and interchanges with RIDGIDs plastic chip tray). The system double-filters and recirculates oil as the chip tray catches the big waste pieces and the filter strains out any small particles. OLBUCKT1 features a sturdy nozzle made from turned aluminum. This system ships with one gallon of Reed Threadguard dark cutting oil (#06120). Additionally the Reed OLBUCKT1 provides a much-requested 60" (1524 mm) hose. OLBOT1 is a kit that allows pumping oil directly from gallon bottles. OLBOT1 fits Reed OGD (#06120) and OGC (#06112) gallons to allow pumping direct from a container. OLKIT1 is the oil gun hose cap clamp and seal.
Minimize
|
|
Go To Store
|
|
|
Easily create perfect-fitting patch panels using our Shrink
... Read more
Easily create perfect-fitting patch panels using our Shrinker-Stretcher Set Professionals or frequent hobbyists who work on several cars a year will appreciate the compound 451 leverage that offers effortless forming without having to make relief cuts, heating or hammer-forming. Use this Shrinker-Stretcher Set to fabricate gentle radius bends and contours in steel, aluminum, stainless or copper.Mild steel up to 18-gaugeStainless steel up to 20-gaugeAluminum up to 16-gaugeFabricate gentle radius bendsand contours 451 leverage Eastwood's Shrinker/Stretcher Set can reproduce wheel well flanges, dog legs and trunk corners. Can accommodate up to 18 gauge aluminum. Set includes shrinker jaw, stretcher jaw and two housings. Be sure both units are firmly attached to your workbench or use the Vise Mount Base (28051) for proper leverage during operation.Replicate such components as wheel-well flanges, compound dog legs, even trunk corners...form almost anything requiring the combination of a curve and an angle. Both tools can produce curves as tight as 3 radius. Hardened steel jaws will provide years of normal-use service, but if you're working with stainless or a lot of carbon steel, the jaws will tend to wear out over time see Accessories tab for replacement jaws. Made in the USA. Eastwood Shrinker/Stretcher Set includes shrinker and stretcher jaws assembled in their own housings, 2 handles, instructions. A mounting plate is not included see Accessories tab. 28149 Replacement Shrinker Jaw28150 Replacement Stretcher Jaw28051 Mounting Plate Download Shrinker Stretcher Set product instructions PDFShrinker/Stretcher Installation Operating Instructions Use appropriate eye and hand protection when handling sheet aluminum or steel. 28053 7730 CURVES SHRINKING STRETCHING BASE REPRODUCE CURVE EAS28053 EMMS EMUT FABKIT FABRICATING TOOLS FMETAL FORMING FORM FORMER METALSHOP HPMETAL METAL SHAPING SHRINKERS STRECTHERS JAW JAWS MOUNT METAL SHOP MSCATWP PORTO METAL FORMERS PEXTO SHRINKER-STRETCHER SET SHRINKER/STRETCHER SET TMS1
Minimize
|
This store is not yet rated
|
FREE Shipping
Go To Store
|
|
|
|
|
from $156
(2 stores)
See Details
|
|
|
Also known as: LIS-17432, LIS17432; Features and Benefits:
... Read more
Also known as: LIS-17432, LIS17432; Features and Benefits: Translucent jug holds 18 gallons and will not warp with hot oil Rolls easily with four heavy-duty 2 1/2ā wheels Metal tubes extend working area from 36 1/2ā to 77ā Drains from the bottom with a brass drain valve Large 15ā funnel has a built in strainer to catch drain plugs18 Gallon Oil Lift Drain has a quick release and height adjustment.Ā Do your oil changes without making a mess on the floor.
Minimize
|
|
FREE Shipping
Go To Store
|
|
|
MPN #KWW104-0001-15. Kwik-Way LIGHTING LATHE. Most Shop Equ
... Read more
MPN #KWW104-0001-15. Kwik-Way LIGHTING LATHE. Most Shop Equipment products are available for in-store pickup from Advance Auto Parts.
Minimize
20% OFF no Min. Free SHIP +$75. Code: P20
In stock
|
|
FREE Shipping
Go To Store
|
|
|
|
|
from $16
(8 stores)
See Details
|
|
|
|
|
from $156
(2 stores)
See Details
|
|
|
Underground Enclosure Assembly, Pc, Cover Logo Lighting, No
... Read more
Underground Enclosure Assembly, Pc, Cover Logo Lighting, Nominal Length 12 In., Nominal Width 12 In., Nominal Height 12 In., Cover Bolt Type 2 Stainless Steel Hex Head Bolts 3/8-16 X 1 1/2, Cover Pull Slot Size 1/2 X 2 In, Color Gray, Material Of Construction Monolithic Polymer Concrete, Description/special Features Stackable, Open Bottom Box W/ Cover, Non-deliberate Traffic Only, Load Rating 8000 Lbs., Standards Ul Listed To Ansi/scte 77 2007 Tier 8
Minimize
|
|
Go To Store
|
|
|
|
|
from $72
(5 stores)
See Details
|
|
|
|
|
from $72
(5 stores)
See Details
|
|
|
High-End Concours Paint Gun helps you spray-on a beautiful
... Read more
High-End Concours Paint Gun helps you spray-on a beautiful collector-car finish...yet it's powered by your home compressor with only 4 cfm 29 psiThere's no need to buy an expensive professional paint gun when Eastwood's full-size HVLP Concours Paint Gun has the same high-end features, but at 20 of the cost And your home compressor provides all the air power you need (4 cfm 29 psi) to work with this Concours paint gun.Includes 3 stainless steel needle/nozzle/air caps (1.2, 1.4 and 1.8mm)Anodized adjustment knobs and air cap ringLightweight, satin-finished aluminum bodyCompatible with most home-shop compressorsBacked by Eastwood's 10-year limited warrantyRequires only 4cfm 29psi The Eastwood Concours HVLP gravity-feed paint gun is an aluminum-bodied gun built for working comfort, reliability and years of service. With a working pressure of 29 psi and requiring only 4 cfm, this gun is ideal for the professional or hobbyist. The needle/nozzle and passages are stainless steel, making it compatible with both solvent and waterborne coatings. Includes tool kit and 1/4 NPT connection. 51550 Eastwood HVLP Gun with 1.2mm Cap/Needle/Nozzle for basecoats51552 1.4mm Cap/Needle/Nozzle for clear coats51553 1.8mm Cap/Needle/Nozzle for primers51550B Teflon-Coated Aluminum Cup, 600cc 51550A Plastic Cup, 600cc 51136 Eastwood Paint Chip Chart 29953 34-oz. DeKups Disposable-Cup Starter Kit51559 Digital Regulator50207 DeKups Adapter50040ZP Master Paint Kit20474 4-Stage Air Dryer System51537 Complete Garage Air Line System10194ZP PRE Painting Prep 30 oz.51561Z Liquid Ice Buffing System Download instructions in PDF formatIntroductionSpecifications4 CFM 29 PSI max. working pressure at the air inlet, 10 PSI max. at the Air CapM16 x 1.5NPS cup attachment threads14 NPT Air Inlet threads SET-UP A 5/16 I.D. minimum air hose at a 25' maximum length is recommended for best results. A smaller I.D. hose and greater length may produce unsatisfactory results.Review complete instructions and become familiar with the feel of the gun.Clean out cup and gun with solvent to remove any residual manufacturing impurities and dry thoroughly.OperationPlease note that many variables affect the adjustment of a paint gun such as paint viscosity and type, atmospheric conditions and operator preference. The following are some guidelines to get started but some time spent acquiring the feel of the gun and test spraying on sheets of masking paper are recommended before applying paint to your car. Always tune the gunbefore each use as conditions may not be the same as the previous use. 1. The Fan control knob (smaller blue knob at the top rear of gun) is opened by turning in a counter-clockwise direction. This controls the size of the spray pattern or fan and the droplet size. Out with the knob larger pattern/larger droplet size, in smaller pattern/smaller droplet size.2. The Fluid Needle control knob (larger blue knob, below the fan control) is opened by turning in a counter-clockwise direction. This controls the amount of paint flow to the nozzle. Out with the knob more paint,less atomization, in less paint.3. The Air Valve control knob (small blue knob at the bottom of the gun near the air inlet) is opened by turning in a counter-clockwise direction. This is a fine tuning for air flow in the gun. You generally want to start out fully open and decrease air as needed.4. With practice you will quickly acquire a feel for the gun and will be producing professional results.Maintenance and CleaningNoteIt is extremely important that the gun be disassembled and cleaned afterevery use1. Pour out then wipe out any remaining paint in the cup, fill the cup with water (for water borne paints) or sol
Minimize
|
This store is not yet rated
|
FREE Shipping
Go To Store
|
|
|
Underground Enclosure Cover, Pg, Cover Logo Lighting, Cover
... Read more
Underground Enclosure Cover, Pg, Cover Logo Lighting, Cover Bolt Type 2 Stainless Steel Hex Head Bolts 3/8-16 X 2 3/4, Cover Pull Slot Size 1/2 X 4 In, Length 23 1/4 In, Width 13 3/4 In, Depth 2 In, Color Gray, Material Of Construction Monolithic Polymer Concrete, For Use With 15 1/2x25 Enclosures, Load Rating 8,000 Lbs., Description/special Features For Areas With Non-deliberate Traffic Only, Standards Ul Listed To Ansi/scte 77 2007 Tier 8
Minimize
|
|
Go To Store
|
|
|
|
|
from $41
(2 stores)
See Details
|