> soundstorm cr12dvc rms

This new concentric vented heater enhances the capabilities ... Read more

This new concentric vented heater enhances the capabilities of customers to deliver endless hot water in air constrained areas with simple, single penetration installation. This indoor unit provided up to 9.8 gallons of hot water per minute, ideal for homes with up to 4 showers. Requires zero venting clearance, it's a natural gas model with temperature settings from 100-180 degrees Fahrenheit. PVC cannot be used for venting. Use only Category III 3-inch by 5-inch concentric-type stainless steel venting. Note: All water heaters of any type must be installed by a trained and licensed technician. Failure to do so may result in damage, injury or death. Warranties may be void if installed by non-licensed personnel. We will not be held liable for any damages, injury or death caused by proper or improper installation of hot water heaters. We will not be held liable for any local state, county or city code violations caused by the improper selection of water heaters. Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

3M Super Close SCP725W projector displays crystal-clear ima ... Read more

3M Super Close SCP725W projector displays crystal-clear images from only 50 away. This benefits you as you can project a quality image from a close range compared to an average projector that needs 10 feet to project same quality image. 3M projector is an overhead projector that can be installed easily. You can install it in wall mount in a closed or open position or place it in a table. 3M Super Close SCP725 overhead projector has been developed using DLP and Vikuiti Technology. DLP Technology enables High Definition Multimedia Interface 3D capability and closed caption. Vikuiti Technology is a 3M patented Technology that eliminates shadow creation. 3M projector works with camcorders document cameras DVD players and tablets. It transforms any classroom into interactive environment.Features Choose any interactive software that fits your lesson plans. Effortlessly weave together a tapestry of words graphics and video. Features very latest DLP project Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

L3 Square DVC 2 OHM 12" SUBWOOFER square SoloKon™ polypropy ... Read more

L3 Square DVC 2 OHM 12" SUBWOOFER square SoloKon™ polypropylene cone with Santoprene rubber surround,power range: 200-400 watts RMS (200 watts per voice coil),frequency response: 25-500 Hz Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

Rubber Sheet, General Purpose, High Grade, Neoprene Rubber, ... Read more

Rubber Sheet, General Purpose, High Grade, Neoprene Rubber, Thickness 1/16 In, Width 12 In, Length 12 In, Black, Smooth Finish, Plain Backing Type, Min Temp Rating -30 F, Max Temp 225 F, Durometer 50a, Elongation 350%, Tensile Strength 1500 Psi, Standards Astm D2000 Bc Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

The new CR8400 series of wire lead transformers provides a ... Read more

The new CR8400 series of wire lead transformers provides a high quality solution, at low cost for current sensing. Major applications include ground fault relays, current measurements, power monitoring and over/under current sensing. This series of transformers provides the benefit of a high accuracy remote monitor for cost sensitive projects. They are epoxy encapsulated to provide protection from the environment. Electrical insulation is rated at 100M ohm at 500 Vdc. Detailed information is available for operation in 50 to 400 Hz systems. The CR Magnetics CR8400 series of current transformers are constructed using core material of a high grade laminated nickel alloy or silicon steel material. The styles have window opening sizes of 0.232" diameter with 0.709", to 1.181" O.D. Operating temperature: -25 degree C to +66 degree C, Insulation resistance: 100 M ohms at 500 Vdc, High potential: 1500 volts x 1 minute. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Frequency: 50 to 400 Hz. Minimize

Sony XS-GS120LD Experience increased output with minimal di ... Read more

Sony XS-GS120LD Experience increased output with minimal distortion using the XS-GS120LD 12" GS Series Dual Voice Coil (DVC) subwoofer. Constructed using Mica reinforced cellular composite for reduced weight and increase rigidity, this subwoofer delivers deep bass response. It also uses a powerful, high energy Ferrite magnet to control cone travel and deliver big power handling. Additionally, this subwoofer is rated for 400 watts, 520 watts RMS (CEA 2031 rated) and can handle peak power of 1500 watts. Minimize

New 3000W MA Audio 12" Inch HK Sub DVC 2 Ohm Subwoofer New ... Read more

New 3000W MA Audio 12" Inch HK Sub DVC 2 Ohm Subwoofer New 12" MA Audio Hard Kore Series HK12X2 3000 Watt DVC Competition Subwoofer Features: (1)MA Audio HK12X2 Subwoofer 3000 Watts Power Handling 1500 Watts RMS Power Handling 400 Oz. Double Stacked Strontium Magnets Aluminum Round Wire Voice Coil Hi-Temp Kapton Voice Coil Former Patented Thermo-Cooling Motor Structure Bumped Back Plate for Max Excursion High Roll Triple Layer Ribbed Surround Double Layer Progressive Spiders Dual Layer Pressed Carbon Fiber Cone Ultra Strong Carbon Fiber Dust Cap Rubber Sealant Gasket Specifications: Sensitivity: 88.9 dB@ 1w/1m Impedance: Dual 2 Ohm Voice Coils Diameter: 12" Mounting Depth 8" Mounting Diameter 11" Vented Box: 3.0 cu/ft Sealed Box: 1.5-2.25 cu/ft Minimize

L3 Square DVC 4 OHM 12" SUBWOOFER square SoloKon™ polypropy ... Read more

L3 Square DVC 4 OHM 12" SUBWOOFER square SoloKon™ polypropylene cone with Santoprene rubber surround,power range: 200-400 watts RMS (200 watts per voice coil),frequency response: 25-500 Hz Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

Rubber Sheet, General Purpose, High Grade, Neoprene Rubber, ... Read more

Rubber Sheet, General Purpose, High Grade, Neoprene Rubber, Thickness 1/8 In, Width 12 In, Length 12 In, Black, Smooth Finish, Plain Backing Type, Min Temp Rating -30 F, Max Temp 225 F, Durometer 50a, Elongation 350%, Tensile Strength 1500 Psi, Standards Astm D2000 Bc Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute. Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

The CR Magnetics CR8300 series electrical current transform ... Read more

The CR Magnetics CR8300 series electrical current transformers are available in both wire lead and printed circuit board styles. The PCB styles are mountable for automated assembly and feature a non-symmetrical mounting hole pattern to ensure correct orientation. Core material is a high grade laminated nickel alloy material to provide very low ratio error and phase angle error. The CR8300 series of transformers is designed to meet requirements of IEC 1036 and ANSI C12 for electric metering. They are designed to operate in 50 or 60 Hz systems. Silicon Steel cores provide moderate accuracy and lower cost for applications such as current measurement and current relaying. Nickel Alloy cores are for applications that require highest accuracy with minimal phase angle error and are higher in cost. Applications would include power and energy monitoring devices. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Insulation Resistance: 100 M ohms at 500 Vdc. High Potential: 1500 volts x 1 minute, Frequency: 50 to 400 Hz. Case material: polypropylene resin. Construction: epoxy: encapsulated. Minimize

Flat Outside Surface with Round Tubing Inside Surface for C ... Read more

Flat Outside Surface with Round Tubing Inside Surface for Comfortable Grip Excellent Match for CRL Geneva, Vienna, Concord, Cardiff, and Other Square Cornered Hinges Stocked in Several Popular Finishes The NEW RM Series Back-to-Back Handles offer features from both the popular SQ and MT Series Handles). The RM Series Handle has a flat outside surface, thus having the square cornered appearance of the SQ Series. Therefore it is a good choice for similar CRL Hinge Series such as Geneva, Vienna, Concord, Cardiff, and others. The inside portion of the handle has the same round tubing as the MT Series Handle, ensuring a comfortable grip.SPECIFICATIONS:Material: 3/4" (19 mm) Brass Tubing; 1-1/4" (31.8 mm) Metal WashersGlass Thickness Range: 1/4" (6 mm) to 1/2" (12 mm)Hole Diameter Required: 1/2" (12 mm)Center-to-Center Hole Spacing: 6" (152 mm); 8" (203 mm) Minimize

The new CR8400 series of wire lead transformers provides a ... Read more

The new CR8400 series of wire lead transformers provides a high quality solution, at low cost for current sensing. Major applications include ground fault relays, current measurements, power monitoring and over/under current sensing. This series of transformers provides the benefit of a high accuracy remote monitor for cost sensitive projects. They are epoxy encapsulated to provide protection from the environment. Electrical insulation is rated at 100M ohm at 500 Vdc. Detailed information is available for operation in 50 to 400 Hz systems. The CR Magnetics CR8400 series of current transformers are constructed using core material of a high grade laminated nickel alloy or silicon steel material. The styles have window opening sizes of 0.232" diameter with 0.709", to 1.181" O.D. Operating temperature: -25 degree C to +66 degree C, Insulation resistance: 100 M ohms at 500 Vdc, High potential: 1500 volts x 1 minute. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Frequency: 50 to 400 Hz. Minimize

The new CR8400 series of wire lead transformers provides a ... Read more

The new CR8400 series of wire lead transformers provides a high quality solution, at low cost for current sensing. Major applications include ground fault relays, current measurements, power monitoring and over/under current sensing. This series of transformers provides the benefit of a high accuracy remote monitor for cost sensitive projects. They are epoxy encapsulated to provide protection from the environment. Electrical insulation is rated at 100M ohm at 500 Vdc. Detailed information is available for operation in 50 to 400 Hz systems. The CR Magnetics CR8400 series of current transformers are constructed using core material of a high grade laminated nickel alloy or silicon steel material. The styles have window opening sizes of 0.232" diameter with 0.709", to 1.181" O.D. Operating temperature: -25 degree C to +66 degree C, Insulation resistance: 100 M ohms at 500 Vdc, High potential: 1500 volts x 1 minute. Maximum continuous primary current 4 X Ir, storage temperature -45 degree C thru +85 degree C, operating temperature general purpose and Nickel -40 degree C thru +85 degree C, operating temperature high frequency -40 degree C thru +65 degree C. Frequency: 50 to 400 Hz. Minimize