> Lighting > Track & Monorail > YLighting

The V/A Sphere is a suspended 4 foot diameter system includ ... Read more

The V/A Sphere is a suspended 4 foot diameter system including twenty-four 10W light points.Kit Contents:12 X factory bent and cut V/A track sections8 X straight V/A track sections4 X horizontal angle connector 90°6 X horizontal cross connectors8 X isolating connectors4 X suspension clips1 X suspension plate4 X V/A adapters2 X 300W power feedsTechnical Specifications:2 X 300W circuitry designed for an additional four 50 watt pendantsFixtures and 600W transformer are sold separately. Choose from Bruck's large selection of Uni-Light pendants. Minimize

This remote magnetic transformer converts standard 120 or 2 ... Read more

This remote magnetic transformer converts standard 120 or 277 volt line voltage to 12 volts, providing the necessary voltage for powering Two-Circuit MonoRail low-voltage lighting system. Each transformer includes fast-acting secondary circuit breakers that will safely turn the system off should a short occur. Once the short has been removed the breakers can be reset. Transformer powers lamp totaling up to 600 watts.This transformer must be installed in a remote but accessible location (such as above the ceiling or in a closet). To simplify installation the transformer should be located no more than 20 feet from the run or power feed. The electrician will need to supply the proper gauge conductor from the transformer to the power feed location based on distance (see voltage drop chart).Dimming a transformer may create a buzzing sound, which may be objectionable in some applications. Debuzzing dimming coils can be purchased to reduce audible noise (sold separately). Minimize

This single-feed surface transformer converts standard 120 ... Read more

This single-feed surface transformer converts standard 120 volt line voltage to 24 volts to provide the necessary voltage for powering a MonoRail low-voltage lighting system. It can power lamps totaling up to 600 watts. The transformer is concealed inside a decorative housing with a fast acting secondary circuit breaker that will safely turn the system off should a short occur. Once the short has been removed the breaker can be reset.This surface transformer includes a preinstalled debuzzing dimming coil to reduce audible noice when using a low-voltage dimmer.Black and white finish have satin nickel feeds. The shortest rigid standoff that can be used with this surface transformer is 5" rigid standoff (sold separately). If dropping the rail more than 5" below the ceiling, order the desired rigid standoff length and one compatible power extender (sold separately). This surface transformer may be plugged in with the addition of a Plug Option, a 16 foot cord with plug (sold separately). Minimize

This dual-feed surface transformer converts standard 120 vo ... Read more

This dual-feed surface transformer converts standard 120 volt line voltage to 12 volts to provide the necessary voltage for powering a MonoRail low-voltage lighting system (2 X 12V 300W circuits). It can power lamps totaling up to 600 watts. The transformer is concealed inside a decorative housing with a fast acting secondary circuit breaker that will safely turn the system off should a short occur. Once the short has been removed the breaker can be reset.This surface transformer includes a preinstalled debuzzing dimming coil to reduce audible noice when using a low-voltage dimmer.Black and white finish have satin nickel feeds. The shortest rigid standoff that can be used with this surface transformer is 5" rigid standoff (sold separately). If dropping the rail more than 5" below the ceiling, order the desired rigid standoff length and two compatible power extenders (sold separately). This surface transformer may be plugged in with the addition of a Plug Option, a 16 foot cord with plug (sold separ Minimize

The 96" Enzis Kit utilizes Bruck's light weight Enzis track ... Read more

The 96" Enzis Kit utilizes Bruck's light weight Enzis track system. Available in bronze or matte chrome. Two malleable aluminum rods in the flexible track hold the desired shape even when used with suspended cable supports. It is easily field bendable to achieve any radius or hard angle, eliminating the need for angle connectors or predetermined radius measurements. The system is attached using 3 supports and transformer with power feed. Fixtures are directionally adjustable and location can be set as desired.This preconfigured kit contains all you need for a 96 inch run with 5 Tikus or Pira heads.Kit Contents:Enzis 300W surface mount electronic transformer2 X Enzis end capsEnzis 96" track3 X Enzis ceiling supports5 X Enzis Pira Spot or Enzis Tikus fixtures5 X 50W MR16 36° lampsTechnical Specifications:300VA transformer120V AC, 50/60Hz input11.7V AC output250VA, 248W for 5 (maximum 50 watt lamps)Suitable for dry locations onlyMounts to 3" - 4" round junction boxShort circuit, overload Minimize

V/A double tier suspended ring system. Composed of 8 V/A tr ... Read more

V/A double tier suspended ring system. Composed of 8 V/A track segments, 4 dual clip spacers, 8 track spacers, 12 cable suspensions, and 4 power feeds. 4 separate 300W circuits total. All other materials sold separately. Minimize

From the magnetic transformer series by WAC Lighting, comes ... Read more

From the magnetic transformer series by WAC Lighting, comes the SRT-1000M. This remote transformer converts standard 120V to 12 or 24V and provides up to four circuits with 250W. Magnetic transformers allow for greater wiring distances from the transformer to the powered equipment. While they are larger in size than it's electronic counterpart, Magnetic transformers provide greater capacities and power boost taps which increase voltage from 12V up to 15V or from 24V up to 30V to compensate for voltage drop.Features:"Push-to-reset" circuit breakers.Automatic resetting thermal protector on the primary side.Knock out holes on both sides, for convenient wiring.Output screw terminals for secure connections.Dimmable with Low Voltage Magnetic or Standard Incandescent Dimmers (Depending on Dimmer Model). Minimize

The V/A Kit 39 utilizes Bruck's versatile V/A track system. ... Read more

The V/A Kit 39 utilizes Bruck's versatile V/A track system. The power feed canopy is designed to give users the flexibility to center it on the track, or at an offset with supports.This kit is designed to get you started with all the components needed for the rail system. Then it can be customized with Bruck Uni-Light fixtures or pendants and connectors, sold separately.Kit Contents:V/A 150W surface mount electronic transformer with cover2 X V/A end caps1 X V/A 39" straight track1 X V/A support with clipTechnical Specifications:120V AC, 50/60Hz input11.7V AC output150VA, 148W for 3 (maximum 50 watt lamps)140VA, 138W for 4 (maximum 35 watt lamp)140VA, 138W for 7 (maximum 20 watt lamp)Suitable for dry locations onlyMounts to 3" - 4" round junction boxShort circuit, overload and thermal protectionsDimmableCan be used wuth Bruck's LED pendants Minimize

This high-quality brushed nickel finish three-light monorai ... Read more

This high-quality brushed nickel finish three-light monorail lighting kit from LBL lighting includes everything from the transformer to the bulbs. The features of this system include: Flexible power connector - transformer does not need to be positioned directly over the rail Positionable heads with grip area Telescopic rail supports so that rail can be installed close to ceiling or far enough away to get around pipes, ductwork, etc. LBL pendant lights and swivel lights can be added, as long as the transformer's maximum wattage is not exceeded This kit consists of the following items: 1 X 4 foot monorail 3 X monorail light fixtures 3 X MR16 halogen lightbulbs 2 X ceiling support (allows installation height of 12" - 24") 1 X 150W electronic transformer (36" power supply to rail that can be shortened) 2 X rail endcaps Minimize

This single-feed surface magnetic transformer converts stan ... Read more

This single-feed surface magnetic transformer converts standard 120 line voltage to 12 volts to provide the necessary voltage for powering a Two-Circuit MonoRail low-voltage lighting system. It can power lamps totaling up to 500 watts with 250 watts maximum on each circuit. The transformer is concealed inside a decorative housing with a fast acting secondary circuit breaker that will safely turn the system off should a short occur. Once the short has been removed the breaker can be reset.This product can mount to either a 4" square electrical box with round plaster ring or an octagon electrical box (not included).Preinstalled debuzzing coils are included to reduce audible noise when using a low-voltage dimmer.Black and white finish have satin nickel feeds. The shortest rigid standoff that can be used with this surface transformer is the 6" rigid standoff (sold separately). If dropping the rail more than 6" below the ceiling, order the desired rigid standoff length and one compatible power exten Minimize

V/A double tier suspended ring system. Composed of 6 V/A tr ... Read more

V/A double tier suspended ring system. Composed of 6 V/A track segments, 3 dual clip spacers, 6 track spacers, 9 cable suspensions, and 3 power feeds. 3 separate 300W circuits total. All other materials sold separately. Minimize

The Flight Spiral is a 3 foot diameter spiral with 4 turns ... Read more

The Flight Spiral is a 3 foot diameter spiral with 4 turns and an 8 foot length/height.This kit is designed to get you started with all the components needed for the Flight Spiral configuration.Kit Contents:300W remote electronic transformer (T-300/120V)6 X Track sectionsEnd caps, connectors, suspension mounting, lamps and power feedTechnical Specifications:120V AC, 60Hz input12V/12.6V (boost tap) AC output288W for 240 (1.2W watt lamp)Suitable for dry locations onlyAuto thermo shutoff (resettable) on primary; 25A switch circuit breaker on secondary20,000 hour lamp life Minimize

These remote magnetic transformers convert standard 120 or ... Read more

These remote magnetic transformers convert standard 120 or 277 volt line voltage to 12 volts, providing the necessary voltage for powering Two-Circuit MonoRail low-voltage lighting system. Each transformer includes fast-acting secondary circuit breakers that will safely turn the system off should a short occur. Once the short has been removed the breakers can be reset. Transformers can power lamps totaling up to 1200 watts.This transformer must be installed in a remote but accessible location (such as above the ceiling or in a closet). To simplify installation the transformer should be located no more than 20 feet from the run or power feed. The electrician will need to supply the proper gauge conductor from the transformer to the power feed location based on distance (see voltage drop chart).Dimming a transformer may create a buzzing sound, which may be objectionable in some applications. Debuzzing dimming coils can be purchased to reduce audible noise (sold separately). Minimize

V/A suspended ring system. Composed of 4 V/A track segments ... Read more

V/A suspended ring system. Composed of 4 V/A track segments, 4 connectors, 12 cable suspensions, and 2 power feeds. 2 separate 300W circuits total. All other materials sold separately. Minimize

This monorail kit allows the creation of a straight, 96" ru ... Read more

This monorail kit allows the creation of a straight, 96" run. With adjustable angle, "T" and "X" connectors (sold separately), other configurations are possible - some confirgurations may require cutting the rail, which is easily accomplished in the field. For use with LBL lighting monorail light fixtures. This kit includes: - 2 X 48" straight rails - 1 X straight conductive connector - 1 X surface mounted 300W electronic transformer with 36" of flexible coaxial feeder cable - 3 X telescoping rigid standoffs (6"-10") - 4 X end caps Minimize

The V/A Kit 78 utilizes Bruck's versatile V/A track system. ... Read more

The V/A Kit 78 utilizes Bruck's versatile V/A track system. Uses two 39" tracks joined together to form a straight 78" connection. The power feed canopy is designed to give users the flexibility to center it on the track, or at an offset with supports.This kit is designed to get you started with all the components needed for the rail system. Then it can be customized with Bruck Uni-Light fixtures or pendants and connectors, sold separately. Kit Contents:V/A 300W surface mount electronic transformer with cover2 X V/A end caps2 X V/A 39" straight track1 X V/A track connector2 X V/A support with clipTechnical Specifications:120V AC, 50/60Hz input11.7V AC output300VA, 298W for 6 (maximum 50 watt lamps)280VA, 278W for 8 (maximum 35 watt lamp)300VA, 298W for 15 (maximum 20 watt lamp)Suitable for dry locations onlyMounts to 3" - 4" round junction boxShort circuit, overload and thermal protectionsDimmableNOT compatible with LED fixtures Minimize

Surface mount magnetic low voltage transformer for Solorail ... Read more

Surface mount magnetic low voltage transformer for Solorail™ system. The canopy style enclosure includes the transformer and the track power feed adapter.Features:Output circuit breaker located on the upper lip of the canopy enclosure is a magnetic push to reset type.Contains integral de-buzzing coil.Minimum Wattage: 1WMaximum Wattage: 24V, 600W.Standard height matches the LM-X5 (5 ¾") suspension standoff height.Overall height can be increased by the use of two LM-R extension rods and LM-RI extension rod couplers.Dimmable with Low Voltage Magnetic Dimmer.Available in Chrome, Brushed Nickel and Dark Bronze finishes. Minimize

Design by Hannes Wettstein for Zed, 2000.Made in Italy by P ... Read more

Design by Hannes Wettstein for Zed, 2000.Made in Italy by Pallucco.Pendant lamp on horizontal zinc-colored painted metal rod, which can be wall or ceiling mounted. The adjustable, swivel parabolas are in a semi-gloss aluminum finish. Minimize

V/A double tier suspended ring system. Composed of 4 V/A tr ... Read more

V/A double tier suspended ring system. Composed of 4 V/A track segments, 2 dual clip spacers, 4 track spacers, 6 cable suspensions, and two power feeds. 2 separate 300W circuits total. All other materials sold separately. Minimize

Design by Castor, 2007.Mood lighting for rock stars.Guitar ... Read more

Design by Castor, 2007.Mood lighting for rock stars.Guitar pedals are the inspiration for this light. 12-volt rubber truck lights plug into a power box using guitar jacks. Lights can then be placed anywhere using metal pucks and magnets.Provides direct and ambient illumination. Available in one, three or five light versions. 12V transformer is included and is housed in the metal box. Includes toggle switches and LED indicator lights.Groupings:DG-1: 1 X 48"L cordDG-3: 1 X 48"L and 2 X 24"L cordsDG-5: 2 X 48"L and 3 X 24"L cords Minimize

Kits are the easiest way to order MonoRail. Each kit comes ... Read more

Kits are the easiest way to order MonoRail. Each kit comes with all the power and hardware you need for most basic installations. Magnetic surface transformer mounts to a standard 4" junction box (provided by electrician), rail drops 4.8" from ceiling. Add up to six 50 watt elements, up to eight 35 or 37 watt elements, or up to fifty 5.8 watt LED elements (sold separately).All MonoRail kits include: 8 foot long hand bendable MonoRail.Two sets of decorative end capsTwo rigid standoff supports300 watt surface mounted magnetic transformer with power feedCustomize your kit with these options (sold separately):MonoRail drop optionsMonoRail extender optionsTech Lighting low voltage heads Minimize

The V/A Wave is a pre-configured system that provides the r ... Read more

The V/A Wave is a pre-configured system that provides the rail and components to form a 10 foot by 3 foot rectangle with curved rails (Wave). The V/A Wave can be mounted directly onto the ceiling.Kit Contents:9 X factory curved V/A track sections8 X straight V/A track sections4 X horizontal angle connector 90°2 X horizontal cross connectors6 X horizontal T connectors5 X isolating connectors8 X cord suspension clips2 X 300W power feeds30 foot power supply cable1 X T-600/120V transformerTechnical Specifications:120V AC, 50/60Hz input11.7V AC output300W max per circuitNOT compatible with LED fixturesFixtures are sold separately. Choose from Bruck's large selection of Uni-Light fixtures and pendants. Minimize

Kits are the easiest way to order MonoRail. Each kit comes ... Read more

Kits are the easiest way to order MonoRail. Each kit comes with all the power and hardware you need for most basic installations. Remote Transformer installs in an accessible location behind the ceiling or wall. Canopy mounts to a standard 4" junction box (provided by electrician), rail drops 2" from ceiling. Add up to six 50 watt elements, up to eight 35 or 37 watt elements or up to fifty 5.8 watt LED elements (sold separately).All MonoRail kits include:8 foot long hand bendable MonoRail.Two sets of decorative end capsTwo rigid standoff supports300 watt remote mounted magnetic transformer with canopy and power feedCustomize your kit with these options (sold separately):MonoRail drop optionsMonoRail extender optionsTech Lighting low voltage heads Minimize

This monorail kit allows the creation of a soft, M-shaped w ... Read more

This monorail kit allows the creation of a soft, M-shaped wave, a circle, or a question mark shaped curve. For use with LBL lighting monorail light fixtures. This kit includes: - 3 X 20" curved rails (24" diameter, 1/3 round, 12" radius) - 3 X straight conductive connectors - 1 X surface mounted 300W electronic transformer with 36" of flexible coaxial feeder cable - 3 X telescoping rigid standoffs (6"-10") Minimize

Surface mount magnetic low voltage transformer for Solorail ... Read more

Surface mount magnetic low voltage transformer for Solorail™ system. Designed to power two separate sections of rail, the LM-EN12-600M model has two 300W 12V feeds. The canopy style enclosure includes the transformer and the track power feed adapter.Features:Output circuit breaker located on the upper lip of the canopy enclosure is a magnetic push to reset type.Contains integral de-buzzing coil.Minimum Wattage: 1WMaximum Wattage: 12V, 600W (2 X 300W).Standard height matches the LM-X5 (5 ¾") suspension standoff height.Overall height can be increased by the use of four LM-R extension rods and LM-RI extension rod couplers.Dimmable with Low Voltage Magnetic Dimmer.Available in Chrome, Brushed Nickel and Dark Bronze finishes. Minimize