> car audio amplifier

PACKAGE: RE AUDIO XT V3 SERIES XT4000DE V3 1600 WATT RMS (4 ... Read more

PACKAGE: RE AUDIO XT V3 SERIES XT4000DE V3 1600 WATT RMS (4000 WATT DYNAMIC) POWER CLASS D COMPACT MONO SUBWOOFER CAR AMPLIFIER WITH BUILT IN ADJUSTABLE 24 Db / OCTAVE BUTTERWORTH CROSSOVER NETWORK + CADENCE WK01 COMPLETE 0 GAUGE WIRE KIT Features: XT4000DE V3 1,600 watt RMS (4000w peak) mono car amplifier Class "D" fully digital power supply 4000 watts peak output 1,600w x 1 RMS @ 1 ohms 950w x 1 RMS @ 2 ohms 550w x 1 RMS @ 4 ohms Bridgeable Efficiency: 86 % @ 4 Ohms or 84 % @ 2 Ohms or 76 % @ 1 ohm Fully adjustable butterworth low pass crossover filter Low Pass Crossover Filter - Adjustable 40 - 250 HZ @ 24 dB per octave Adjustable Bass Equalizer: 24 dB Bass Boost @ 45 HZ Subsonic Filter: 15-40 HZ @ 24 dB per octave Low level Input RCA Pre-amp output Pass through output for multiple amp installs Block Power Connector Requires true 0 gauge power wire for installation Screw terminal barrier strip speaker connectors 8 - 18 AWG speaker connector gauge Aluminum heatsink Convention cooling power and protection LED Indicators Class D Frequency Response: 20 HZ - 500 HZ Thermal, Overload, Short circuit, DC Offset protection Fuse Rating: 90A (3x30A fuses) Damping Factor: 150 Low Input Impedance: 22 Ohm Input sensitivity: 200/8.0 Free bass Remote Included S/N Ratio: 80 dB Weight: 13 pounds Dimensions: 1.875" x 10" x 15.75" 17' - 0 Gauge Translucent Blue SuperFlex Power Cable 3' - 0 Gauge Translucent Black SuperFlex Ground Cable Gold Plated ANL Heat Resistance Fuse Holder 200 Amp ANL Gold Plated Fuse 1 - 17' High Grade Twisted Pair of RCA Interconnects 25' Translucent Blue Speaker Wire 7' Split Loom Tubing 17' Amplifier Remote Turn On Cable Wire Ties and Ring Terminals, and all other accessories you need for a clean installation Minimize

Product Features: 2000W Peak, 8-Channel Class D Power Ampl ... Read more

Product Features: 2000W Peak, 8-Channel Class D Power Amplifier RMS Power Rating: 8 ohms: 150 watts x 8 chan. 4 ohms: 250 watts x 8 chan. Bridged, 8 ohms: 500 watts x 4 chan. Rackmount design allows you to install the amplifier in any standard equipment rack 10/100 Ethernet jack that allows you to control and monitor the amplifier's functions Mixer section allows you to route an input to any and all outputs Ethernet port allows you to store up to 35 DSP presets and subpresets Stepped and calibrated attenuator knob for each input DC Voltage control and remote power on/off Built-In protection circuitry protects against overloads and overheating Low-Z, 25V, 70V and 100V Models Extensive DSP Available Easy and intuitive user interface Power switch can be disabled by software 4-Step Signal Level and Clip LEDs Power, standby, protect, network, temperature, and current LED indicators Temperature sensitive variable-speed fans Damping Factor: >250 Maximum Input Level: +21dBu Input Sensitivity: 6.2dBu Input Impedance: 20k ohms, balanced Frequency Response: 20-20,000 Hz, (unweighted) ± 1dB Signal-to-Noise Ratio: >105 dB Dimensions: 15-1/2inD x 19inW x 3-1/2inH Safety/Compliance: CE, FCC, RoHS Optional CobraNet, EtherSound, AES/EBU, Mic Preamps 1-year Manufacturer's warrantyInputs & Outputs 8 x Euroblock Inputs 1 x AC Power Input 1 x Input Expansion Slot 8 x Euroblock Speaker Outputs 1 x 10/100 Ethernet Port 1 x Remote Level Control 1 x Data I/O Ports 1 x Preset Recall 1 x Remote Power Standby Minimize

Product Features: 1000W Peak, 4-Channel Class D Power Ampl ... Read more

Product Features: 1000W Peak, 4-Channel Class D Power Amplifier RMS Power Rating: 8 ohms: 150 watts x 4 chan. 4 ohms: 250 watts x 4 chan. Bridged, 8 ohms: 500 watts x 2 chan. Rackmount design allows you to install the amplifier in any standard equipment rack 10/100 Ethernet jack that allows you to control and monitor the amplifier's functions Mixer section allows you to route an input to any and all outputs Ethernet port allows you to store up to 35 DSP presets and subpresets Stepped and calibrated attenuator knob for each input DC Voltage control and remote power on/off Built-In protection circuitry protects against overloads and overheating Low-Z, 25V, 70V and 100V Models Extensive DSP Available Easy and intuitive user interface Power switch can be disabled by software 4-Step Signal Level and Clip LEDs Power, standby, protect, network, temperature, and current LED indicators Temperature sensitive variable-speed fans Damping Factor: >250 Maximum Input Level: +21dBu Input Sensitivity: 6.2dBu Input Impedance: 20k ohms, balanced Frequency Response: 20-20,000 Hz, (unweighted) ± 1dB Signal-to-Noise Ratio: >105 dB Dimensions: 15-1/2inD x 19inW x 3-1/2inH Safety/Compliance: CE, FCC, RoHS Optional CobraNet, EtherSound, AES/EBU, Mic Preamps 1-year Manufacturer's warrantyInputs & Outputs 4 x Euroblock Inputs 1 x AC Power Input 1 x Input Expansion Slot 4 x Euroblock Speaker Outputs 1 x 10/100 Ethernet Port 1 x Remote Level Control 1 x Data I/O Ports 1 x Preset Recall 1 x Remote Power Standby Minimize

Product Features 2400W Peak, 2-Channel Class D Power Ampli ... Read more

Product Features 2400W Peak, 2-Channel Class D Power Amplifier RMS Power Rating: 8 ohms: 700 watts x 2 chan. 4 ohms: 1200 watts x 2 chan. Bridged, 8 ohms: 2400 watts x 1 chan. Integrated Protea DSP allows graphic and/or parametric EQ, high and low pass filters, time delay, etc. Rackmount design allows you to install the amplifier in any standard equipment rack 10/100 Ethernet jack enables control and monitoring of the amplifier's functions DC voltage control Remote power standby Stepped and calibrated attenuator knob for each channel Input slot available for optional CobraNet CNM-2 card or an AES/EBU input Built-In protection circuitry protects against overloads and overheating Power, standby, protect, network, temperature, current, and power switch disable status LED indicators 4-Level signal and clip LEDs Cooling: Temperature sensitive variable-speed fan, front-in, rear-out flow Input Sensitivity: 26 or 32 dB or 1.4V Input Impedance: 20k ohms, balanced Frequency Response: 20-20,000 Hz ± 1dB Damping factor: >250 (8 ohm load, Minimize

This is a VR3 VRA2.0 200 watt, 2-channel car audio amplifie ... Read more

This is a VR3 VRA2.0 200 watt, 2-channel car audio amplifier. This 200 (50 Watts RMS x 2 @ 4 Ohm) watt amplifier features an adjustable 3-position (Bass, Treble, Flat) crossover. It is ideal for driving a single subwoofer or a pair, or you can also use it run your highs or component system. By being equipped with this built-in crossover (50 Hz - 250 Hz), you won't have to spend extra money on additional crossovers. This MOSFET amplifier also has a RCA line input and line output, which can be used for daisy chaining additional amplifiers. Additionally, the adjustable sensitivity and bass boost dials, allow you the flexibility to dial in the perfect amount of bass to suit your car stereo system. This unit has been remanufactured to 100% of its original factory specifications. Minimize

Roswell Wake Air 500.1 Amp Rma Amplifier . The RMA 500.1 is ... Read more

Roswell Wake Air 500.1 Amp Rma Amplifier . The RMA 500.1 is a true power house mono amplifier that packs the hardest punch in the smallest package in its class with true 500 watt RMS power. Fine tuning adjustment can be made with the supplied remote gain control. Features High efficiency Class G/H Internal fan Reversed heat sinks to dissipate heat Fully marinized with water repellant and anti corrosion spray on circuit board Remote GAIN control (supplied) Advanced Diagnostic System Small installation foot print Specifications POWER OUTPUT 4? - 312 Watts X 1 14.4V POWER OUTPUT 4? - 509 Watts X 1 14.4V TOTAL HARMONIC DISTORTION - 0.05% FREQUENCY RANGE - 20Hz-200Hz CROSS OVER RANGE - 30Hz-2000Hz BASS BOOST - 0-15Db 30Hz-125Hz S/N RATIO (a WTG) REF 4? - >82Db OVERALL DIMENSION - 11.7 (297.18MM)L X 5.9 (150mm)W X 2 (52mm)H Minimize

The all-in-one CDG-6000RV is a variable speed CD/CD+G/Casse ... Read more

The all-in-one CDG-6000RV is a variable speed CD/CD+G/Cassette mixing amplifier that is perfect for dance or music applications. Variable speed on both the CD/CD+G and the Cassette player will allow you to enhance your music output by changing the speed to match your needs. The CDG-6000RV has microphone inputs with features including Digital Reverb and Digital Echo that will make any performer sound like a star. The rack-mountable CDG-6000RV will connect easily to your house system with mixed output through XLR or use the internal amp for smaller venues. These professional features provide a key component to any setup and we think you will agree that the CDG-6000RV provides the best sound on the market.The CDR-1000 PRO is a Stand-Alone CD burner, designed for quick burning of music and vocals on the road or on stage and it does not even require a computer. How is that for convenience! The Record-Duo RV package is a stand alone package that comes with everything you need to start mixing and recording your Karaoke music. 250W, Professional Variable Speed Digital Key Control CD/CD+G/Cassette CD Recording System Package Includes: 1 CDG-6000RV 250W Variable Speed CD/CD+G/Cassette Player/Mixing Amp with Digital Reverb and Digital Echo 1 CDR-1000 PRO Professional Single Space CD Recorder/Player 1 RC-6 Carpeted Road Case 1 VX-8 Stereo 8” Vocal Speaker System 2 MARK-38 Professional Vocal Microphones 1 SS-88 Speaker Stand for optional mounting Authorized Internet Dealer 1-year Manufacturer's warranty Mixing Amplifier Specifications: 125W + 125W maximum power output at 8 Ohms Built-in variable speed, skip-free, shock-resistant CD/CD+G player Built-in variable speed cassette deck with record level control and led meter 13-step digital key controller Bass and treble controls for microphone and music Digital echo and reverb for professional sounding vocals Vocal cancel/partner modes for removing vocals on multiplexed media 120/230V switchable Remote control PAL/NTSC switchable Effect loop Audio Inputs: 2 A/V (RCA) and 1 AUX. (RCA) Mic Inputs: 3 XLR, 3 1/4in Jack Audio Outputs: 2 audio (RCA) (Rec & Pre-Out), 1/4in headphone out, XLR L/R Video Outputs: 1 video (RCA) stereo speaker outStand Alone CD Burner Specifications: Rack-mountable, requiring only 1 RU of rackspace Instant one-touch “finalizing” of CD-R/RWs Create CDs that can be played in a standard CD player One-touch erasing of CD-RW discs RCA and XLR audio line in/out connections 1/4in Headphone jack so you can monitor your recording Recording Volume control for pro-sounding recordings Instant one-touch “finalizing” of CD-R/RWs Create CDs that can be played in a standard CD player One-touch erasing of CD-RW discs RCA and XLR audio line in/out connections 1/4in Headphone jack so you can monitor your recording Recording Volume control for pro-sounding recordings Instant one-touch “finalizing” of CD-R/RWs Create CDs that can be played in a standard CD player One-touch erasing of CD-RW discs RCA and XLR audio line in/out connections 1/4in Headphone jack so you can monitor your recording Recording Volume control for pro-sounding recordingsVocal Speaker System Specifications: 8” Vocal Speaker System Professional carpeted cabinet w/ casters Speakers designed for live entertainment with faithful vocal reproduction Stereo six-way speaker system for great sound distributionMicrophone Specifications: Black Leatherette Finish Sensitivity - 70 dB Frequency Response 50 - 14000Hz Impedance: 600 ohm Pro 20' Detached Cord Includes a Pro Mic Carrying Case and Holder Net Weight: 11 ozSpeaker Stand Specifications: STAND Top Adjusts from 1 3/8in to 1 1/2in Diameter to fit most popular speakers Adjustable Height from 42in up to 82in Black Finish Minimize

Brand New Re Audio DTS-1500.1 2000 Watt DTS Series Monobloc ... Read more

Brand New Re Audio DTS-1500.1 2000 Watt DTS Series Monoblock Car Amplifier Features: DTS Series Monoblock Class D Car Amplifier Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Variable Bass Boost (0 to +12 dB bass boost at 45 Hz) Bridgeable with multi link technology (MLT) Mono channel operation Preamp RCA outputs to daisy chain multiple amps 2-Way System Protection circuitry (thermal and short circuit) Dual speaker terminals simplify the hookup of multiple speakers Heavy duty brushed aluminum alloy convection fan cooled heatsink for efficient heat dissipation Nickel-plated RCA level inputs Nickel-plated 12AWG screw terminals Minimize

General Features: 2 Channel Touring Amplifier with Binding ... Read more

General Features: 2 Channel Touring Amplifier with Binding Posts High power density – The FP 4000 delivers a total of 4000 W (2 x 2000 W @ 2 ohms) in only 2U Lab.gruppen sound quality – FP 4000 amplifiers maintain the Lab.gruppen’s reputation for sound quality, with transparent mid- and high-frequency performance and new circuit designs optimized for sustained low-frequency output NomadLink® network ready – Monitoring and control of key functions accessible via the intuitive DeviceControl software and the robust, daisy-chained NomadLink® network, as well as by the leading third party control platforms Patented Class TD® amplifier topology – Road-proven output stage delivers Class B audio quality with Class D efficiency Regulated Switch Mode Power Supply (R.SMPS™) – Outputpower remains constant even with significant drops in the mains voltage Efficient cooling system – Unique, lightweight Intercooler® copper cooling system dissipates more heat to allow extended peak output Adjustable parameters – Selectable Gain, scalable Voltage Peak Limiter (VPL™), and bridge-mode operation allow custom configuration for any system or application XLR input and link connectors Heavy-duty binding post or Speakon™ output connectors Comprehensive protection and warning – Excessive output current, DC, high temperature, very high frequency (VHF), short circuit, open load, mains fuse protection, and soft start 1-year Manufacturer's warrantyPower Output: Number of channels: 2 Peak total output both channels driven: 4000 W Peak output voltage per channel: 121 V Max. output current per channel: 50 A peak MAX Power Rating: 16 ohms: 400 watts x 2 chan. 8 ohms: 800 watts x 2 chan. 4 ohms: 1600 watts x 2 chan. 2 ohms: 2000 watts x 2 chan. MAX Power Rating Bridged: Bridged, 16 ohms: 1600 watts x 1 chan. Bridged, 8 ohms: 3200 watts x 1 chan. Bridged, 4 ohms: 4600 watts x 1 chan. Performance with Gain: 35 dB and VPL: 150 V THD 20 Hz - 20 kHz for 1 W: 70 dB Frequency response (1 W into 8 ohms) +0/-3 dB: 2 Hz - 34.2 kHz Input impedance: 20 kOhm Input Common Mode Rejection, CMR: 45 dB Output impedance @ 100 Hz: 56 mOhmVoltage Peak Limiter (VPL), max. peak output VPL, selectable per ch: 121, 101, 83, 70, 56, 47, 38V VPL, selectable when bridged: 242, 202, 166, 140, 112, 94, 76V Voltage Peak Limiter mode (per ch.): Hard / SoftGain and Level: Amplifier gain selectable (all channels) rear-panel switches: 23, 26, 29, 32, 35, 38, 41, 44 dB Default gain: 38 dB Level adjustment (per ch.): Front-panel potentiometer, 31 position detented from -inf to 0 dBConnectors and Switches: Input connectors (per ch.): 3-pin XLR, electronically balanced Output connectors (per ch.): Neutrik Speakon or Binding Posts (must be specified upon order) Output bridge mode: A+B - Ch. A is signal input source NomadLink® network: On board, 2 x RJ45 EtherCon connectors, IN and OUT Intelligent fans (on/off): Yes, depending on presence of output signal Power on/off and Remote enable on/off: Individual switches on front-panel Cooling: Two fans, front-to-rear airflow, temperature controlled speedFront-panel indicators: Common: NomadLink Network; Power Average Limiter (PAL) 2); Power on Per channel: Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal;Voltage Peak Limiter (VPL); Current Peak Limiter (CPL); Very High Frequency (VHF); High temperature; Fault; MutePower: Operating voltage (230V / 115V nominal): 130-265V / 65-135V Minimum power-up voltage: 230V / 115V 171V / 85V Power Average Limiter (PAL): Yes Soft start / Inrush Current Draw Yes / max. 5 A Mains connector 230 V CE: 16 A, CEE7; 115 V ETL: 20 A / NEMA 5-20PSpecifications: Dimensions: (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”) Weight: 12 kg (26.4 lbs.) Finish: Black painted steel chassis with gray painted steel front Approval Minimize

ONE xXx 1600 WATT CAR 2 CHANNEL CLASS AB AMPLIFIER BRAND NE ... Read more

ONE xXx 1600 WATT CAR 2 CHANNEL CLASS AB AMPLIFIER BRAND NEW IN THE PACKAGE Features : One xXx two channel class AB car audio amp Power rating (RMS / MAX):220 Watts x 2 /800 Watts x 2 Bridged power: 1600 Watts x 1 Frequency response:20Hz - 20kHz Signal to noise ratio: 103dB Channel separation: 65dB Min. speaker impedance:2 Ohms stereo, 4 Ohms mono bridged Variable bass boost Bridgeable outputs Tri-mode capable Remote bass knob included Thermal and speaker short protection Crossover range (Low p Minimize

Factory Direct Car Audio and Video "We're all about custome ... Read more

Factory Direct Car Audio and Video "We're all about customer satisfaction!" 2,000 WATT 4 GAUGE AMPLIFIER INSTALLATION KIT - RED This kit has everything you need! LOWEST PRICE....GUARANTEED!! BRAND NEW!! This complete amp kit has everything you need to hook up your amplifier to your battery, head-unit, and speakers/subwoofers. It can handle up to 2,000 Watts.Unlike other kits on ebay, this kit has high quality OFC (Oxygen-Free Copper)power and speaker wire - see pics below. Included in the Kit : Minimize

General Features: 2 Channel Touring Amplifier with Binding ... Read more

General Features: 2 Channel Touring Amplifier with Binding Posts High power density – The FP 13000 delivers a total of 13000 W (2 x 6500 W @ 2 ohms) in only 2U Lab.gruppen sound quality – FP 13000 amplifiers maintain the impeccable sonic performance standards set by the original fP Series, with the same durability and even greater efficiency. NomadLink® network ready – Monitoring and control of key functions accessible via the intuitive DeviceControl software and the robust, daisy-chained NomadLink® network, as well as by the leading third party control platforms Patented Class TD® amplifier topology – Road-proven output stage delivers Class B audio quality with Class D efficiency Regulated Switch Mode Power Supply (R.SMPS™) – Outputpower remains constant even with significant drops in the mains voltage Efficient cooling system – Unique, lightweight Intercooler® copper cooling system dissipates more heat to allow extended peak output Adjustable parameters – Selectable Gain, scalable Voltage Peak Limiter (VPL™), and bridge-mode operation allow custom configuration for any system or application XLR input and link connectors Heavy-duty binding post output connectors Comprehensive protection and warning – Excessive output current, DC, high temperature, very high frequency (VHF), short circuit, open load, mains fuse protection, and soft start 1-year Manufacturer's warrantyPower Output: Number of channels: 2 Peak total output both channels driven: 13000 W Peak output voltage per channel: 195 V Max. output current per channel: 82 A peak MAX Power Rating: 16 ohms: 1200 watts x 2 chan. 8 ohms: 2350 watts x 2 chan. 4 ohms: 4400 watts x 2 chan. 2 ohms: 6500 watts x 2 chan. MAX Power Rating Bridged: Bridged, 16 ohms: 4700 watts x 1 chan. Bridged, 8 ohms: 8800 watts x 1 chan. Bridged, 4 ohms: 13000 watts x 1 chan. Performance with Gain: 35 dB and VPL: 190 V THD 20 Hz - 20 kHz for 1 W: 70 dB Frequency response (1 W into 8 ohms) +0/-3 dB: 2 Hz - 34 kHz Input impedance: 20 kOhm Input Common Mode Rejection, CMR: 54 dB Output impedance @ 100 Hz: 56 mOhmVoltage Peak Limiter (VPL), max. peak output VPL, selectable per ch: 195, 170, 140, 116, 100, 80, 66, 54V VPL, selectable when bridged: 390, 340, 280, 232, 200, 160, 132, 108V Voltage Peak Limiter mode (per ch.): Hard / SoftGain and Level: Amplifier gain selectable (all channels) rear-panel switches: 23, 26, 29, 32, 35, 38, 41, 44 dB Default gain: 35 dB Level adjustment (per ch.): Front-panel potentiometer, 31 position detented from -inf to 0 dBConnectors and Switches: Input connectors (per ch.): 3-pin XLR, electronically balanced Output connectors (per ch.): Binding Posts (2-pole) Output bridge mode: A+B - Ch. A is signal input source NomadLink® network: On board, 2 x RJ45 EtherCon connectors, IN and OUT Intelligent fans (on/off): Yes, depending on presence of output signal Power on/off and Remote enable on/off: Individual switches on front-panel Cooling: Two fans, front-to-rear airflow, temperature controlled speedFront-panel indicators: Common: NomadLink Network; Power Average Limiter (PAL) 2); Power on Per channel: Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal;Voltage Peak Limiter (VPL); Current Peak Limiter (CPL); Very High Frequency (VHF); High temperature; Fault; MutePower: Operating voltage (230V / 115V nominal): 130-265V / 65-135V Minimum power-up voltage 230V / 115V: 171V / 85V Power Average Limiter (PAL): Yes Soft start / Inrush Current Draw Yes / max. 5 A Mains connector: 230V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lockSpecifications: Dimensions(W/H/D): W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”) Weight: 12 kg (26.4 lbs.) Finish: Black painted steel chassis with gray painted steel front Approvals: CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC Minimize

Roswell Wake Air 500.4 Amp Rma Amplifier . This RMA marine ... Read more

Roswell Wake Air 500.4 Amp Rma Amplifier . This RMA marine amplifier uses a Full Range Class G/H topography that significantly improves efficiency while enhancing sound quality. Formulated coating to protect your investment. Class G/H amplifiers make more power for their size than traditional designs and offer much lower THD and higher damping factors than Full Range Class D amplifiers. Features High efficiency Class G/H Internal fan Reversed heat sinks to dissipate heat Fully marinized with water repellant and anti corrosion spray on circuit board Expandable for multiple units Multi application Crossover Controls Advanced Diagnostic System Small installation foot print Specifications POWER OUTPUT 4? - 75 Watts X 4 14.4V POWER OUTPUT 4? - 125 Watts X 4 14.4V TOTAL HARMONIC DISTORTION - 0.05% FREQUENCY RANGE - 1Hz-69Hz CROSS OVER RANGE - 55Hz-600Hz BASS BOOST - 0-15Db 42Hz S/N RATIO (a WTG) REF 4? - >90Db OVERALL DIMENSION - 11.7 (297.18MM)L X 5.9 (150mm)W X 2 (52mm)H Minimize

The SAX-125.2 was designed to replace our SAX-100.2 model - ... Read more

The SAX-125.2 was designed to replace our SAX-100.2 model -- it features an upgraded power supply for a bit more power as well as greatly enhanced crossover flexibility. This unit was built to satisfy the discerning audiophile who doesn't necessarily want to spend huge sums of money on his full range amplifier. This amplifier utilizes high quality Sanken bipolar output transistors, and 12 of them at that! The SAX-125.2 is also equally suited for subwoofer applications where tremendous power is not called for. * 2/1 Channel Bridgeable Class-AB Amplifier * MOSFET PWM Power Supply * Stable Into 4 Ohms Bridged or 2 Ohms Stereo Load * 12dB Octave Electronic Crossover Slope * Variable Subsonic Filter * High Pass Filter Variable with x 10 Range Selectable Switch * Low Pass Filter Variable with x 10 Range Selectable Switch * HPF/FULL/LPF Selectable Switch * Variable Bass Boost Control * Variable Bass-Boost Frequency Control * Variable Input Level Control * Input Sensitivity : 200mV ~ 6V * Subsonic Filter : 10Hz ~ 500Hz * Signal Input and Line Out RCA Connectors * Multi-Way Protection circuitry (Thermal/Over Current/Speaker Short/Speaker DC protection) * Tested Voltage & THD: 14.4V & Less than 0.05% THD * Operating Voltage : DC10V~16V Power Input * Wired Remote Controller RMS power, 4 ohm stereo 125W x 2CH RMS power, 2 ohm stereo 200W x 2CH RMS power, 4 ohm bridged 400W x 1CH Signal to Noise Ratio >90dB Low pass frequency crossover 50Hz ~ 5KHz High Pass Crossover 30Hz ~ 3KHz Variable Subsonic Filter 10Hz to 500Hz Bass Boost 0~18dB Variable Bass-Boost Frequency Control 35Hz to 120Hz Frequency Response 10Hz ~ 40KHz (+/-1dB) THD@RMS Watts <0.1% Channel Separation 75dB Fuse Rating 20A x 3 Input Sensitivity Variable 200mV~6V (+/- 5%) Dimensions 252(W) x 58(H) x 340(L)mm Minimize

General Features: 2 Channel Touring Amplifier with Binding ... Read more

General Features: 2 Channel Touring Amplifier with Binding Posts High power density – The FP 14000 delivers a total of 14000 W (2 x 7000 W @ 2 ohms) in only 2U Lab.gruppen sound quality – The FP 14000 is optimized for sustained performance into extreme low-frequency loads, yet it also maintains Lab.gruppen’s reputation for exceptionally smooth and transparent mid- and high-frequency response. NomadLink® network ready – Monitoring and control of key functions accessible via the intuitive DeviceControl software and the robust, daisy-chained NomadLink® network, as well as by the leading third party control platforms Patented Class TD® amplifier topology – Road-proven output stage delivers Class B audio quality with Class D efficiency Regulated Switch Mode Power Supply (R.SMPS™) – Outputpower remains constant even with significant drops in the mains voltage Efficient cooling system – Unique, lightweight Intercooler® copper cooling system dissipates more heat to allow extended peak output Adjustable parameters – Selectable Gain, scalable Voltage Peak Limiter (VPL™), and bridge-mode operation allow custom configuration for any system or application XLR input and link connectors Heavy-duty binding posts Comprehensive protection and warning – Excessive output current, DC, high temperature, very high frequency (VHF), short circuit, open load, mains fuse protection, and soft start 1-year Manufacturer's warrantyPower Output: Number of channels: 2 Peak total output both channels driven: 14000 W Peak output voltage per channel: 195 V Max. output current per channel: 83 A peak MAX Power Rating: 16 ohms: 1200 watts x 2 chan. 8 ohms: 2350 watts x 2 chan. 4 ohms: 4400 watts x 2 chan. 2 ohms: 7000 watts x 2 chan. MAX Power Rating Bridged: Bridged, 16 ohms: 4700 watts x 1 chan. Bridged, 8 ohms: 8800 watts x 1 chan. Bridged, 4 ohms: 14000 watts x 1 chan. Performance with Gain: 35 dB and VPL: 190 V THD 20 Hz - 20 kHz for 1 W: 70 dB Frequency response (1 W into 8 ohms) +0/-3 dB: 2 Hz - 34.2 kHz Input impedance: 20 kOhm Input Common Mode Rejection, CMR: 54 dB Output impedance @ 100 Hz: 56 mOhmVoltage Peak Limiter (VPL), max. peak output VPL, selectable per ch: 195, 170, 140, 116, 100, 80, 66, 54V VPL, selectable when bridged: 390, 340, 280, 232, 200, 160, 132, 108V Voltage Peak Limiter mode (per ch.): Hard / SoftGain and Level: Amplifier gain selectable (all channels) rear-panel switches: 23, 26, 29, 32, 35, 38, 41, 44 dB Default gain: 38 dB Level adjustment (per ch.): Front-panel potentiometer, 31 position detented from -inf to 0 dBConnectors and Switches: Input connectors (per ch.): 3-pin XLR, electronically balanced Output connectors (per ch.): Binding Posts (2-pole) Output bridge mode: A+B - Ch. A is signal input source NomadLink® network: On board, 2 x RJ45 EtherCon connectors, IN and OUT Intelligent fans (on/off): Yes, depending on presence of output signal Power on/off and Remote enable on/off: Individual switches on front-panel Cooling: Two fans, front-to-rear airflow, temperature controlled speedFront-panel indicators: Common: NomadLink Network; Power Average Limiter (PAL) 2); Power on Per channel: Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal;Voltage Peak Limiter (VPL); Current Peak Limiter (CPL); Very High Frequency (VHF); High temperature; Fault; MutePower: Operating voltage (230V / 115V nominal): 130-265V / 65-135V Minimum power-up voltage 230V / 115V: 171V / 85V Power Average Limiter (PAL): Yes Soft start / Inrush Current Draw Yes / max. 5 A Mains connector: 230V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lockSpecifications: Dimensions(W/H/D): W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”) Weight: 12 kg (26.4 lbs.) Finish: Black painted steel chassis with gray painted steel front Approvals: CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 600 Minimize