> Building Supplies > water heaters > Jobsite Equipment and Protective Gear

GeoSpring Hybrid Water Heater Brand New In Box - Current Mo ... Read more

GeoSpring Hybrid Water Heater Brand New In Box - Current Model GEH50DEEDSC Saves $325 every year* in water heating expenses (*Based on DOE test procedures and comparison of 50-gallon standard electric tank water heaters using 4879 kWh per year vs. the GeoSpring hybrid water heater using 1830 kWh per year) Uses up to 62% less energy than a standard electric 50-gallon water heater Proudly assembled in Louisville, KY Provides the same hot water recovery as a traditional 50-gallon standard electric water heater with 65 gallons first hour rating Installs like a standard electric water heater with the same water and electrical connections Limited 10 year warranty provides peace of mind and dependability X ENERGY STAR® Qualified ENERGY STAR® is a government-backed program helping businesses and individuals protect the environment through superior energy efficiency. 4,500 Watts Electrical Circuit Required 208V/240V 60 Hz Dedicated 30 Amp Min. Operating Water Pressure 20-125 PSI (30-80 PSI recommended) Electrical Cons Minimize

Watts Floodsafe Water Detector Shutoff for Gas Water Heater ... Read more

Watts Floodsafe Water Detector Shutoff for Gas Water Heaters - Standing Pilot, Right Hand Thread This is a brand new water heater shutoff (model # WDS-SP-R). Emergency unit automatically shuts off both water supply and power source when water is detected on the floor or in the drain pan beneath the water heater; help protect property from catastrophic flood damage. Can be installed on new or existing water heaters and easily reset to assure proper operation. Power Cutout Modules for standing pi Minimize

Munters Sial GRY Portable Indirect Fired Heater - 133000 BT ... Read more

Munters Sial GRY Portable Indirect Fired Heater - 133000 BTU The GRY-I 40 is a compressor heater with stack. This compact design portable and mobile indirect fired heater provides cost effective spot and space heating for an extensive variety of applications including closed or less ventilated premises where people are present over a longer time. This 133,000 BTU heater functions on diesel or kerosene and is very easy to operate. It is primarily designed for drying in buildings and for heating of medium to large premises and is equipped with a safety switch to prevent overheating as well as a rotary air compressor. The Combustion chamber is made out of specially treated temperature resistant stainless steel. With a 710 cfm Airflow, a 12 gallon tank (with a run time of about 13 hours), this durable heater is also suitable for outdoor usage and meeting the requirements of the IPX4D protection class. The GRY-I 40 is set to be connected to a room thermostat (sold separately). This model comes equipped with sturdy handles for easy movement. CSA approved. 45.00 L. 30.00 W. 25.00 H. Minimize

Provides a flush and professional finish,For both Residenti ... Read more

Provides a flush and professional finish,For both Residential and Commercial Outdoor models,Helps to prevent possible tampering,This water heater recess box is for OUTDOOR installation ONLY, and is intended for use only with the water heater models listed above,Recess Box Clearances,Freeze Protection Minimize

Triangle Tube PHASE III Smart 30 Indirect Water Heater Bran ... Read more

Triangle Tube PHASE III Smart 30 Indirect Water Heater Brand New Sealed In Original Box Description: The Smart Choice in Indirect Fired Water Heaters STAINLESS STEEL The decision to use stainless steel for the manufacture of the "Tank in Tank" was made in the 60's. It was chosen for its well established reliability and advantages over other materials, namely: Stainless steel is stable at elevated temperatures above 180ºF, which is not the case for tanks manufactured from mild steel protected by a glass lined coating. It is for this reason that some manufacturers include a clause in their guarantee limiting the DHW storage temperatures to 140°F or even 130°F. Stainless steel, as its name suggests, is resistant to corrosion. The protective coatings in an enameled tank can be damaged by a shock during transportation, unloading or maneuvering it into position. This is not the case with stainless steel. Last, but not least, a stainless steel tank does not need a sacrificial anode. This is a major advantage versus Minimize

AQUAH AQE-21 electric tankless water heater; ETL Certified ... Read more

AQUAH AQE-21 electric tankless water heater; ETL Certified (Certificate No. 4002422); Unique glossy IMD front panel, splash proof, corrosion and aging resistant; Patented technology (Patent No. ZL2008 2 0081568.0), enclosed loop heating system with less heat loss, nano insulation material to completely separate water from electricity; Multi-layer heating chamber with long life span; Electric leakage protection; anti scaling mechanism, and over temperature/water pressure protection; Direct temperature setting, consistent output water temperature regulated by thermostat, and temperature settings automatically memorized to avoid repeated operations; LED touch screen to show the heater's working condition, output water temperature, running time and power/water consumption; Water temperature displayed in either Fahrenheit or Celsius; Fault auto-detection technique for the convenience of trouble shooting. Specifications: Power: 21 KW Voltage/Frequency: 240 V/60 Hz Phase: 1 Maximum amperage: 88 A; Minimum circuit br Minimize

Instant hot water - will heat a gallon of water from 60 deg ... Read more

Instant hot water - will heat a gallon of water from 60 degrees to 130 degrees in 10 minutes. Shockproof and portable; simply immerse directly in bucket or tank. Built for years of service; will not burn out even if operated dry. Stainless steel guard protects hot element from contacting surfaces after removal from water. Unit has an automatic shut-off. Shuts off if water level drops below 51/2". 1000 watts, 120 volt. Minimize

AQUAH AQE-12 electric tankless water heater; ETL Certified ... Read more

AQUAH AQE-12 electric tankless water heater; ETL Certified (Certificate No. 4002422); Unique glossy IMD front panel, splash proof, corrosion and aging resistant; Patented technology (Patent No. ZL2008 2 0081568.0), enclosed loop heating system with less heat loss, nano insulation material to completely separate water from electricity; Multi-layer heating chamber with long life span; Electric leakage protection; anti scaling mechanism, and over temperature/water pressure protection; Direct temperature setting, consistent output water temperature regulated by thermostat, and temperature settings automatically memorized to avoid repeated operations; LED touch screen to show the heater's working condition, output water temperature, running time and power/water consumption; Water temperature displayed in either Fahrenheit or Celsius; Fault auto-detection technique for the convenience of trouble shooting. Specifications: Power: 12 KW Voltage/Frequency: 240 V/60 Hz Phase: 1 Maximum amperage: 50 A; Minimum circuit br Minimize

Robertshaw's 41-400 Series Norton Hot Surface Ignitors deli ... Read more

Robertshaw's 41-400 Series Norton Hot Surface Ignitors deliver dependable ignition in heating systems of every description. From furnaces and boilers to rooftop heaters, infrared burners, unit heaters, water heaters and many other types of HVAC equipment. The 41-400 Series Hot Surface Ignitors are made of high-purity recrystallized silicon carbide (CrystarTM) which combines physical and thermal strength with stable electrical properties. The 41-400 Series are designed to reach ignition temperature(s) within 17 seconds. They have 18-gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity. The lead wires are also enclosed with a special high-temperature fiberglass insulation providing total electrical protection. All 41-400 series ignitors are 120 VAC models. Some hot surface modules are rated for 208/240 volts input, however they step the voltage to ignitor down to 120 VAC. 7.50 L. 5.00 W. 4.50 H. Minimize

Tankless Water Heater - Model IR-6000 Model IR-6000, 8000 i ... Read more

Tankless Water Heater - Model IR-6000 Model IR-6000, 8000 is designed for whole house, can be used for multiple outlets with capacity 0.5 to 4.5 gpm. Install indoors, and can be used in either residential or commercial applications. Our Tankless Hot Water Generators have a fully modulating heating system that use less amperage, can be easily installed in both new and retrofit applications. Super Green Tankless Hot Water Generators are designed to be the most Energy Efficient (99%), the safest and the longest lasting water heating system, while being the most Eco-Friendly product made today. High Power Quartz Far Infra-Red Heating Elements No Metallic No Corrosion No Calcium Deposits Environmentally Friendly Maintenance Free Operational Longevity Recyclable Materials Superior Heating Efficiency * Requires 2 independent 220V AC circuits protected by 2 separate and independent 30 amp double pole breakers (60 Total Amps). Minimum recommended electrical service is 200 amps. Minimize

Tankless Water Heater - Model IR-3000 Model IR-3000, 4000 b ... Read more

Tankless Water Heater - Model IR-3000 Model IR-3000, 4000 best suited for apartment or condo, serving 1 or 2 outlets at a time with capacity 0.5 to 4 gpm. Install indoors, and can be used in either residential or commercial applications. Our Tankless Hot Water Generators have a fully modulating heating system that use less amperage, can be easily installed in both new and retrofit applications. Super Green Tankless Hot Water Generators are designed to be the most Energy Efficient (99%), the safest and the longest lasting water heating system, while being the most Eco-Friendly product made today. High Power Quartz Far Infra-Red Heating Elements No Metallic No Corrosion No Calcium Deposits Environmentally Friendly Maintenance Free Operational Longevity Recyclable Materials Superior Heating Efficiency * Requires 1 independent 220V AC circuit protected by 1 separate and independent 30 amp double pole breaker (30 Total Amps). Minimum recommended electrical service is 200 amps. Minimize

Tankless Water Heater - Model IR-4000 Model IR-3000, 4000 b ... Read more

Tankless Water Heater - Model IR-4000 Model IR-3000, 4000 best suited for apartment or condo, serving 1 or 2 outlets at a time with capacity 0.5 to 4 gpm. Install indoors, and can be used in either residential or commercial applications. Our Tankless Hot Water Generators have a fully modulating heating system that use less amperage, can be easily installed in both new and retrofit applications. Super Green Tankless Hot Water Generators are designed to be the most Energy Efficient (99%), the safest and the longest lasting water heating system, while being the most Eco-Friendly product made today. High Power Quartz Far Infra-Red Heating Elements No Metallic No Corrosion No Calcium Deposits Environmentally Friendly Maintenance Free Operational Longevity Recyclable Materials Superior Heating Efficiency * Requires 1 independent 220V AC circuit protected by 1 separate and independent 40 amp double pole breaker (40 Total Amps). Minimum recommended electrical service is 200 amps. Minimize

Therm 660 EF Natural Gas Eligible for up to $1500 Federal T ... Read more

Therm 660 EF Natural Gas Eligible for up to $1500 Federal Tax Credit (30% of purchase price and residential installation)The Therm 660 EF is compact enough to install virtually anywhere. But dont let the size fool you. This model is loaded with features including freeze protection and built-in high temperature capability (160°F).Features:Super compact 14'' x 20½'' x 7'' size 83%+ thermal efficiency 140,000 BTU maximum input 6.6 gallons per minute capacity at 35F degree rise Minimum activat Minimize

Electric Ceiling Heater, Residential And Light Commercial B ... Read more

Electric Ceiling Heater, Residential And Light Commercial Bathroom, Voltage 120, 1250 Watts, Height 11 In, Width 11 In, Depth 2 3/4 In, Built-in Features Chrome Alloy, Wire Element, Automatic Overheat Protection, Permanently Lubricated Motor, Requires Mounts To 3 1/2 In Or 4 In Round Or 4 In Octagonal Electrical Box Minimize

Watts Floodsafe Water Detector Shutoff for Electric Water H ... Read more

Watts Floodsafe Water Detector Shutoff for Electric Water Heaters - 220VAC This is a brand new water heater shutoff (model # WDS-E220-34). Emergency unit automatically shuts off both water supply and power source when water is detected on the floor or in the drain pan beneath the water heater; help protect property from catastrophic flood damage. Can be installed on new or existing water heaters and easily reset to assure proper operation. Features: Protects property from catastrophic damage due to a water heater leak Automatically detects water on the floor (or in a drain pan) and automatically shuts off the water supply and power source to the water heater System can be easily reset Sized for 3/4" water lines - order code = 0301003 Provides contacts for monitored alarm detection system Max. electric water heater current rating: 30A Minimize

      ... Read more

          Balboa GFCI 40 breaker and box Balboa 40 AMP GFCI breaker "Approved protection for all hot tubs and pools "        Balboa is the world leader in hot tub heaters and controllers. By law and for your saftey, all electrical connections must be protected by a Ground Fault Circuit Interupter. Incase of accidental current leakage the GFI will trip ensuring you and your families protection. This unit is weather proof and can be installed outdoors. By law in most states a hot tub needs to have a emergency shut off located within 5-10 feet of the hot tub. By using a junction box with the GFI included serves as a quick shut off to the pool or hot tub. Proprietary GFCIs installed in your main breaker can cost as much as $400, and if you are using outdoor cable the extra cost will also add to the installation. By putting the GFCI near the hot tub instead of your main breaker panel, you are no longer forced to buy a special breaker designed to fit only your panel. You can also run cheaper indoor cabling to the junction box and terminate and run more pricey out door cable only were needed. This 40 Amp breaker will run most standard hot tubs using 5.5 Kw heater and upto 4 HP pumps and accessories. Minimize

Wire Element Heater - Model 154Chrome Alloy, Wire Element F ... Read more

Wire Element Heater - Model 154Chrome Alloy, Wire Element For Instant HeatLow-Profile Housing With Satin-Finish Aluminum Grille Extends Only 2 3/4" From CeilingBuilt-In Fan Disperses Heat EvenlyAutomatic Overheat ProtectionPermanently Lubricated MotorMounts Easily To Any Standard 3 1/2" Or 4" Round, Or 4" Octagonal Ceiling Electrical BoxMinimum 15-Amp Circuit RequiredSurface-Mount Ceiling Heaters For Quick, Easy Installation. Minimize

Flame Defender Fire Extinguishers There are many electrical ... Read more

Flame Defender Fire Extinguishers There are many electrical devices in today s indoor growing environments. Power strips CO2 generators heat mats lights light movers reservoir heaters fans pumps etc. can malfunction and cause a fire. Protect yourself your growing environment and your home. Install a Flame Defender today! ABC - This is the multipurpose dry chemical extinguisher. The ABC type is filled with monoammonium phosphate a yellow powder that leaves a sticky residue that may be damaging to electrical appliances such as a computer. Dry chemical extinguishers have an advantage over CO2 extinguishers since they leave a non-flammable substance on the extinguished material reducing the likelihood of re-ignition. Class A extinguishers are for ordinary combustible materials such as paper wood cardboard and most plastics. The numerical rating on these types of extinguishers indicates the amount of water it holds and the amount of fire it can extinguish. Class B fires involve flammable or combustible liquids such as gasoline kerosene grease and oil. The numerical rating for class B extinguishers indicates the approximate number of square feet of fire it can extinguish. Class C fires involve electrical equipment such as appliances wiring circuit breakers and outlets. Never use water to extinguish class C fires - the risk of electrical shock is far too great! Class C extinguishers do not have a numerical rating. The C classification means the extinguishing agent is non-conductive. Self contained No plumbing or wiring required. Simply install by attaching vertically to the wall or ceiling. Automatic   extinguishing agent is automatically dispensed if the temperature probe on the unit reaches 155 degrees F. Multi-purpose dry chemical extinguisher. Rated for A B and C. Suitable for electrical fires. Discharges a hemispherical spray pattern in area under sprinkler. Available in three sizes to fit a variety of applications. Coverage Area: 4.4 lb (2 KG) = 4 (1.24 meters diameter) 13.2 lb (6 KG) = 6 (1.8 meters diameter) 26.4 lb (12 KG) = 7.7 (2.3 meters diameter MSRP: $99.95 Minimize

Permanent Split Capacitor Motor. Totally enclosed air over ... Read more

Permanent Split Capacitor Motor. Totally enclosed air over motor. All angle mount ball bearings. UL recognized, CSA certified. Thermally protected. Ideal for unit heaters. Capacitor and base included. Minimize

Broan-NuTone Low-Profile Ceiling HeaterBroan-NuTone Collect ... Read more

Broan-NuTone Low-Profile Ceiling HeaterBroan-NuTone CollectionExclusive Enclosed, Sheathed, Long-Life Element Diffuses Heat Throughout the RoomLow-Profile Housing with Satin-Finish Aluminum Grille Extends Only 2-3/4" From CeilingBuilt-In Fat Disperses Heat EvenlyAutomatic Overheat ProtectionPermanently Lubricated MotorMounts Easily to any Standard 3-1/2" or 4" Round, or 4" Octagonal Ceiling Electrical BoxSurface-Mount Ceiling Heaters are for Quick, Easy Installation1250W, 120VAC Minimize

Flame Defender Fire Extinguishers There are many electrical ... Read more

Flame Defender Fire Extinguishers There are many electrical devices in today s indoor growing environments. Power strips CO2 generators heat mats lights light movers reservoir heaters fans pumps etc. can malfunction and cause a fire. Protect yourself your growing environment and your home. Install a Flame Defender today! ABC - This is the multipurpose dry chemical extinguisher. The ABC type is filled with monoammonium phosphate a yellow powder that leaves a sticky residue that may be damaging to electrical appliances such as a computer. Dry chemical extinguishers have an advantage over CO2 extinguishers since they leave a non-flammable substance on the extinguished material reducing the likelihood of re-ignition. Class A extinguishers are for ordinary combustible materials such as paper wood cardboard and most plastics. The numerical rating on these types of extinguishers indicates the amount of water it holds and the amount of fire it can extinguish. Class B fires involve flammable or combustible liquids such as gasoline kerosene grease and oil. The numerical rating for class B extinguishers indicates the approximate number of square feet of fire it can extinguish. Class C fires involve electrical equipment such as appliances wiring circuit breakers and outlets. Never use water to extinguish class C fires - the risk of electrical shock is far too great! Class C extinguishers do not have a numerical rating. The C classification means the extinguishing agent is non-conductive. Self contained No plumbing or wiring required. Simply install by attaching vertically to the wall or ceiling. Automatic   extinguishing agent is automatically dispensed if the temperature probe on the unit reaches 155 degrees F. Multi-purpose dry chemical extinguisher. Rated for A B and C. Suitable for electrical fires. Discharges a hemispherical spray pattern in area under sprinkler. Available in three sizes to fit a variety of applications. Coverage Area: 4.4 lb (2 KG) = 4 (1.24 meters diameter) 13.2 lb (6 KG) = 6 (1.8 meters diameter) 26.4 lb (12 KG) = 7.7 (2.3 meters diameter MSRP: $149.95 Minimize

Permanent Split Capacitor Motor. Totally enclosed air over ... Read more

Permanent Split Capacitor Motor. Totally enclosed air over motor. All angle mount ball bearings. UL recognized, CSA certified. Thermally protected. Ideal for unit heaters. Capacitor included. Minimize

Slim line 4100 BTU 1200 w Satin 1" dia aluminum grill ext ... Read more

Slim line 4100 BTU 1200 w Satin 1" dia aluminum grill extends 2-1/2" from ceiling Built-in fan Mounts to any standard 3" or 4" electrical box Automatic reset thermal protection Rough in dimensions: 2-1/2"x10-3/4" Minimize

Flexibile, corrosion resistant hot/cold potable water, CTS ... Read more

Flexibile, corrosion resistant hot/cold potable water, CTS (rigid copper tube size), or for use with Quick Connect push on fittings and/or, brass and poly alloy PEX insert barb fittings. Barbed insert PEX fittings are secured using either stainless steel cinch clamps or copper crimp ring methods. Type B Silane method PEX has more antioxidants and thermal stabilizers which is critical for chlorine ratings and recirculation systems. Type A, B, and C are European system designations not rating/grading system for PEX. Do not use duct tape, pipe dope, threading compound, mineral or linseed oil. Support pipe every 30'' vertically and horizontally. Protect pipe when entering/exiting slab or walls. Do not kink or expose to sunlight. Minimum clearance to water heaters, boilers, wood burning appliances. 18''. Recessed lights 12'', gas appliance vents 6''. NSF 61 FDA, CSA/ASTM, UPC listed. Approved 25 year warranty even when used with other manufacturers ASTM SDR 9 certified fittings. Covers materials, labor and not pro rated. Maximum working pressure: 160 P.S.I. (11 bar) at 73.4 F. (23 C) /100 P.S.I. (6.9 bar) at 180 F. (80 C.)/80 P.S.I. (5.5 bar) at 200 F. (93 C.). Manufactured in accordance with American Society for Testing and Materials (ASTM International) F876 and F877 to SDR 9 dimensional standards. Listed by the NSF International to NSF Standards 14 and 61 for use in potable water systems. Listed by NSF International to be in compliant to the Uniform Plumbing Code. Labeled B137.5 which indicates that it is compliant to the CSA Standards B137.5. Certified to PEX 5006 (replaces NSF CL R) for use in continuous hot water recirculation systems. ASTM E84 and CAN/ULC S102.2 smoke developed and flame spread classification. Fire resistance per CAN/ULC S101 and ASTM E119 08. Minimize

Flexibile, corrosion resistant hot/cold potable water, CTS ... Read more

Flexibile, corrosion resistant hot/cold potable water, CTS (rigid copper tube size), or for use with Quick Connect push on fittings and/or, brass and poly alloy PEX insert barb fittings. Barbed insert PEX fittings are secured using either stainless steel cinch clamps or copper crimp ring methods. Type B Silane method PEX has more antioxidants and thermal stabilizers which is critical for chlorine ratings and recirculation systems. Type A, B, and C are European system designations not rating/grading system for PEX. Do not use duct tape, pipe dope, threading compound, mineral or linseed oil. Support pipe every 30'' vertically and horizontally. Protect pipe when entering/exiting slab or walls. Do not kink or expose to sunlight. Minimum clearance to water heaters, boilers, wood burning appliances. 18''. Recessed lights 12'', gas appliance vents 6''. NSF 61 FDA, CSA/ASTM, UPC listed. Approved 25 year warranty even when used with other manufacturers ASTM SDR 9 certified fittings. Covers materials, labor and not pro rated. Maximum working pressure: 160 P.S.I. (11 bar) at 73.4 F. (23 C) /100 P.S.I. (6.9 bar) at 180 F. (80 C.)/80 P.S.I. (5.5 bar) at 200 F. (93 C.). Manufactured in accordance with American Society for Testing and Materials (ASTM International) F876 and F877 to SDR 9 dimensional standards. Listed by the NSF International to NSF Standards 14 and 61 for use in potable water systems. Listed by NSF International to be in compliant to the Uniform Plumbing Code. Labeled B137.5 which indicates that it is compliant to the CSA Standards B137.5. Certified to PEX 5006 (replaces NSF CL R) for use in continuous hot water recirculation systems. ASTM E84 and CAN/ULC S102.2 smoke developed and flame spread classification. Fire resistance per CAN/ULC S101 and ASTM E119 08. Minimize

Motors MODEL 3791 HORSE POWER 1/15 VOLTS 115/230/277 AMPS 1 ... Read more

Motors MODEL 3791 HORSE POWER 1/15 VOLTS 115/230/277 AMPS 1.1 HERTZ 60 FRAME 42Y SHAFT 3/8 DIA X 4.25 BEARINGS BALL SERV. FACT 1 PHASE 1 CAPACITOR 5 MFD / 370V ENCL.ENCLOSED MOUNTING STUDS ROTATION CWLE RPM 1050 PROTECTION AUTOMATIC S89-652 All items we have listed are BRAND NEW in box with complete factory warranty and literature, unless otherwise noted herein. DISCLAIMER All sales are final. Returns ONLY accepted for merchandise not properly represented. You must obtain an RGA prior to any re Minimize

Heated Portable Eyewash Haws heated portable Model 7500EB i ... Read more

Heated Portable Eyewash Haws heated portable Model 7500EB is ideal for remote locations. Using gravity to supply a continuous flow of clean water to injured personnel for a full 15 minutes at .4gpm, this model is a reliable source for safety. Recognizing the 7500 s full patterned flushing feature, and its capability of being used in sub-freezing temperatures, those working in remote areas can t help but feel confident with this piece of emergency equipment day after day. Features: Featuring a FDA high-density green polyethylene tank easily activated by pulling the yellow activation arm down to the open position. 1000 Watt, 120 VAC submergible thermostatically controlled heater produces the ideal temperature in environments as low as -30 degrees. Model supplied with six-foot power cord, 3-prong plug, fitted insulated protective cover and one bottle of bacteriostatic additive. Bacteriostatic additive allows for the storage of water for up to six months, making for a more easily maintained piece of emergency equipment. A wide-fill opening with threaded cap permits easy inspection, cleaning and filling. Relocation is simple due to the easily mounted (bracket included) and light design of this 16 gallon portable. Measurements: 22-1/2" high, 21-1/2" wide, 19-1/2" deep. Model 7500EB is certified by CSA & IAPMO to meet the ANSI Z358.1-2004 Standard for Emergency Eyewash and Shower Equipment. Minimize

PLUG-ON WATER HEATER BREAKER WITH ISOLATED LINE TERMINALS, 2