> Building Supplies > drill/store dk hardware inc

Pro Value CJ1. Adjustable template that locates where to dr ... Read more

Pro Value CJ1. Adjustable template that locates where to drill the holes on your cabinet doors and drawers. Minimize

Provides "Frameless" Look Component to CRL's Cable System f ... Read more

Provides "Frameless" Look Component to CRL's Cable System for 3/8" to 1/2" (10 to 12 mm) Glass CRLs Trim Ring Drill-Thru Shelf Support for 1/2 inch (12 millimeter) glass shelves is a two-part Stainless Steel Clamp that is attached to the Cable with two socket head screws. The Trim Ring sits above the glass and covers the hole for a finished look. The Drill-Thru Support requires a 1/2 inch (12 millimeter) diameter hole for the cable. The weight capacity for each Drill-Thru Shelf Support is 175 pounds (79.4 kilograms). Minimum order is one each. Minimize

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex ... Read more

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex Washer Head, Case-hardened Steel, Zinc Finish, Size #14, Length 1 In, Width Of Hex Head 0.375 In, Head Height 0.190 In, Washer Od 0.520 In, Drill Point Size #3, Drill Point Length 0.393 In, For Attaching Variety Of Materials To Metal, Meets/exceeds Sae J78, Package 100 Minimize

Self Drilling Screw, Sheet Metal, Hex Washer Head, Case-har ... Read more

Self Drilling Screw, Sheet Metal, Hex Washer Head, Case-hardened Steel With Neoprene Washer, Zinc Finish, Size 1/4 In, Length 2 In, Driver Size 3/8 In, Width Of Hex Head 0.367 In, Head Height 0.172 In, Washer Dia 0.480 In, Drill Point Size #3, Drill Point Length 0.393 In, For Attaching Variety Of Materials To Metal Up To 3 Gauge, Meets/exceeds Sae J78, Package 100 Minimize

80/20 Inc 15 Series 1.5"Double Shaft Pre-Drilled Stanchion ... Read more

80/20 Inc 15 Series 1.5"Double Shaft Pre-Drilled Stanchion Mounting Plate, Part #5775 ANO with Clamping Hardware. This 15 Series part measures 6" x 5.5"x 1.45" and has two 1.505" hole bore thru diameters and eight 0.328" drill thru holes.This piece may have a spotty, chalky,imperfect anodize finish with some slight surface scratches but is otherwise fine. It just isn't pretty enough for our factory.Works as shown in second photo. Stanchion clamp screws are included. Note: Tube is NOT included! Minimize

Use our Trave Aluminum Brackets with one of our Wing Glass ... Read more

Use our Trave Aluminum Brackets with one of our Wing Glass or Aluminum Shelves to create a stunning display for your home or office. A 5/16" drill bit (sold separately, listed below) is recommended for installation.||Accommodates shelves up to 12" deep and 3/4" thick | Supports up to 55 pounds | Brackets should be no more than 24" apart | Mounting hardware and instructions are included Minimize

1/4-20 x 3 3/4 Phillips Flat with Wings Self Drill Screw WA ... Read more

1/4-20 x 3 3/4 Phillips Flat with Wings Self Drill Screw WAR Coated - Phillips flat head tapping screw , spaced or unified threads, and a #3 or #4 drill point. Designed to drill through steel to attach wood to metal. AISI 1022 or equivalent steel. Rockwell C50-56. Meets F.I.P.-1000.7 for torsional strength & drill speed. Meets ASTM A 510 for carbon steel manufacturing. Exceeds 1,000/hr. salt spray resistance. Designed to work with ACQ treated lumber. Highly corrosion resistant. Minimize

Hang Vertical Panels Safely and Securely Component to CRL's ... Read more

Hang Vertical Panels Safely and Securely Component to CRL's Cable System for 3/8" to 1/2" (10 to 12 mm) Glass CRLs Drill-Thru Connectors are the ideal product for hanging 3/8 to 1/2 inch (10 to 12 millimeter) glass panels in a high moisture environment where clamping onto the edges of the glass is not the most secure method. The Connector package contains cap, connector base, socket screw, nylon washer and sleeve. Drilling 1/2 inch (12 millimeter) holes in the glass is required. The weight capacity for each Drill-Thru connector is 35 pounds (15.9 kilograms). Minimum order is one each. Minimize

Pocket door hardware by Russell & Erwin featured this lovel ... Read more

Pocket door hardware by Russell & Erwin featured this lovely Greek Revival style pull in their 1887 hardware catalog. Reproduced directly from an antique original, it's a stylish addition to pocket or bi-pass doors. Finely crafted from solid brass, with your choice of lacquered bright brass or antique finishes. Also available in a no-keyhole version. Minimize

Self Tapping Screws are designed to advance when turned, cr ... Read more

Self Tapping Screws are designed to advance when turned, creating their own threads in the material. They are often used in sheet metal and plastic. Steels are designated by a 4 number SAE Steel grade.  The first two digits indicate the primary materials used to form the steel.  The last 2 digits identify the percentage of carbon for the alloy (in hundredths).  The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch).  Zinc Plating helps to prevent corrosion.Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material. Minimize

Self Drilling Screw, Sheet Metal, Hex Washer Head, Case-har ... Read more

Self Drilling Screw, Sheet Metal, Hex Washer Head, Case-hardened Steel, Zinc Finish, Size #8, Length 1/2 In, Drive Type Hex, Driver Size 1/4 In, Width Of Hex Head 0.250 In, Head Height 0.096 In, Washer O 0.272 In Washer O, Drill Point Size #2, Drill Point Length 0.211 In, For Attaching Variety Of Materials To Metal Up To 12 Gauge, Meets/exceeds Sae J78, Package 1410 Minimize

Self Drilling Screw, Sheet Metal, Hex Washer Head, Stainles ... Read more

Self Drilling Screw, Sheet Metal, Hex Washer Head, Stainless Steel, Plain Finish, Size #12, Length 1 1/2 In, Driver Size 5/16 In, Width Of Hex Head 0.305 In, Head Height 0.139 In, Washer Dia 0.398 In, Drill Point Size #3, Drill Point Length 0.353 In, For Attaching Variety Of Materials To Metal Up To 5 Gauge, Meets/exceeds Sae J78, Package 50 Minimize

Typically Used as the Base Channel for Glass Railing System ... Read more

Typically Used as the Base Channel for Glass Railing Systems or Windscreens Drilled and Counter Bored, or We Will Custom Drill to Your Specifications Custom Cutting and Mitering ServiceTest Reports Available The CRL B7S Series Heavy-Duty Square Aluminum Base Shoe is used as the base channel for glass railing systems. It can be clad in several choices of architectural finishes. The most critical component in a railing system is the proper attachment of the Base Shoe to the substrate. CRL has engineered and tested a variety of attachment methods, and has developed an acceptable combination of drilling patterns and fasteners. A printed brochure with Instructions, Installation Hints, Cleaning, and Refinishing techniques is available.All heavy base shoes have a stock length tolerance of plus or minus 3/4 inch (19 millimeter)CAPACITY:3/4 inch (19 millimeter) Thick Glass when using GlassWedge Dry Glaze System or Wet Glaze SystemFor Test Results and Drilling Recommendations, click here.NOTE: 20 feet (6.10 meter) Extrusion Only (without holes) cannot be used for the GlassWedge Dry Glaze System unless the Base Shoe is fabricated to the above tested and approved hole and counter bore pattern. The GlassWedge Dry Glaze System requires that the attachment holes be counter bored so that no part of the fastener protrudes above the base of the channel opening.SHIPPING NOTE: Due to the difficulty in packaging and handling 20 feet (6.10 meters) stock lengths, it is suggested that you Will Call these at any of our distribution centers. If requiring shipment, all packaging and handling concerns must be agreed to by CRL and the customer prior to shipping. All shipping arrangements will be documented on your quotation for your signed approval. Minimize

1/4-20 x 2 3/4 Phillips Flat with Wings Self Drill Screw WA ... Read more

1/4-20 x 2 3/4 Phillips Flat with Wings Self Drill Screw WAR Coated - Phillips flat head tapping screw , spaced or unified threads, and a #3 or #4 drill point. Designed to drill through steel to attach wood to metal. AISI 1022 or equivalent steel. Rockwell C50-56. Meets F.I.P.-1000.7 for torsional strength & drill speed. Meets ASTM A 510 for carbon steel manufacturing. Exceeds 1,000/hr. salt spray resistance. Designed to work with ACQ treated lumber. Highly corrosion resistant. Minimize

Self Tapping Screws are designed to advance when turned, cr ... Read more

Self Tapping Screws are designed to advance when turned, creating their own threads in the material. They are often used in sheet metal and plastic. Steels are designated by a 4 number SAE Steel grade.  The first two digits indicate the primary materials used to form the steel.  The last 2 digits identify the percentage of carbon for the alloy (in hundredths).  The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch).  Zinc Plating helps to prevent corrosion.Pan head fasteners have a low, large cylindrical head with a high rounded top edge for higher tightening torques - these fasteners are often recommended to replace older head styles such as round, binding, or truss-head where possible. The Phillips drive style was originally designed so that the driver would slip out under extreme torque, preventing over-tightening and damage to the fastener or the material. Minimize

Self Drilling Screw, Sheet Metal, Hex Washer Head, Case-har ... Read more

Self Drilling Screw, Sheet Metal, Hex Washer Head, Case-hardened Steel With Neoprene Washer, Zinc Finish, Size 1/4 In, Length 1 In, Driver Size 3/8 In, Width Of Hex Head 0.367 In, Head Height 0.172 In, Washer Dia 0.480 In, Drill Point Size #3, Drill Point Length 0.393 In, For Attaching Variety Of Materials To Metal Up To 3 Gauge, Meets/exceeds Sae J78, Package 100 Minimize

Pocket door hardware with a potted plant with a sadly bent ... Read more

Pocket door hardware with a potted plant with a sadly bent leaf gives this whimsical aesthetic movement pocket door pull design a folksy charm. Aptly named the "Broken Leaf" pattern, it was among the most popular Victorian era hardware designs. This 1880s Lockwood creation has been reproduced in solid brass, with your choice of 3 period finishes. Minimize

"FASTAP" STAINLESS STEEL SCREW Exterior self drilling carp ... Read more

"FASTAP" STAINLESS STEEL SCREW Exterior self drilling carpentry screws QTY Per Box : 35 Duracoat XT coating for all outdoor wood including ACQ, CA, CCA pressure treatments #2 Phillips drive with Power Point Technology for self drilling in all outdoor wood types Minimize

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex ... Read more

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex Washer Head, Case-hardened Steel, Zinc Finish, Size 10-16, Length 1 In, Width Of Hex Head 0.312 In, Head Height 0.120 In, Washer Od 0.414 In, Drill Point Size #3, Drill Point Length 0.300 In, For Attaching Variety Of Materials To Metal, Meets/exceeds Sae J78, Package 100 Minimize

Self Drilling Screw, Sheet Metal, Hex Washer Head, Stainles ... Read more

Self Drilling Screw, Sheet Metal, Hex Washer Head, Stainless Steel, Plain Finish, Size #12, Length 1 In, Driver Size 5/16 In, Width Of Hex Head 0.305 In, Head Height 0.139 In, Washer Dia 0.398 In, Drill Point Size #3, Drill Point Length 0.353 In, For Attaching Variety Of Materials To Metal Up To 5 Gauge, Meets/exceeds Sae J78, Package 100 Minimize

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex ... Read more

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex Washer Head, Case-hardened Steel, Zinc Finish, Size #12, Length 1 1/4 In, Width Of Hex Head 0.312 In, Head Height 0.155 In, Washer Od 0.432 In, Drill Point Size #3, Drill Point Length 0.353 In, For Attaching Variety Of Materials To Metal, Meets/exceeds Sae J78, Package 100 Minimize

Self Tapping Screws are designed to advance when turned, cr ... Read more

Self Tapping Screws are designed to advance when turned, creating their own threads in the material. They are often used in sheet metal and plastic. Steels are designated by a 4 number SAE Steel grade.  The first two digits indicate the primary materials used to form the steel.  The last 2 digits identify the percentage of carbon for the alloy (in hundredths).  The steel used in these fasteners has a tensile strength ranging from 100,000 to 150,000 psi (pounds per square inch).  Zinc Plating helps to prevent corrosion.Hex head fasteners can be driven with simple wrenches, and require minimal clearance above the fastener because they can be driven or loosened from the side. Minimize

Use our Pelicani Aluminum Brackets with one of our Wing Gla ... Read more

Use our Pelicani Aluminum Brackets with one of our Wing Glass or Aluminum Shelves to create a stunning display for your home or office. A 5/16" drill bit (sold separately, listed below) is recommended for installation.||Accommodates shelves up to 12" deep and 1" thick | Supports up to 66 pounds | Brackets should be no more than 24" apart | Mounting hardware and instructions are included Minimize

Self Drilling Screw, Sheet Metal, Hex Washer Head, Stainles ... Read more

Self Drilling Screw, Sheet Metal, Hex Washer Head, Stainless Steel, Plain Finish, Size #14, Length 3/4 In, Driver Size 3/8 In, Width Of Hex Head 0.367 In, Head Height 0.172 In, Washer Dia 0.480 In, Drill Point Size #3, Drill Point Length 0.393 In, For Attaching Variety Of Materials To Metal Up To 3 Gauge, Meets/exceeds Sae J78, Package 50 Minimize

Self Drilling Screw, Sheet Metal, Hex Washer Head, Stainles ... Read more

Self Drilling Screw, Sheet Metal, Hex Washer Head, Stainless Steel, Plain Finish, Size #12, Length 2 In, Driver Size 5/16 In, Width Of Hex Head 0.305 In, Head Height 0.139 In, Washer Dia 0.398 In, Drill Point Size #3, Drill Point Length 0.353 In, For Attaching Variety Of Materials To Metal Up To 5 Gauge, Meets/exceeds Sae J78, Package 50 Minimize

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex ... Read more

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex Washer Head, Case-hardened Steel, Zinc Finish, Size 10-16, Length 1 1/2 In, Width Of Hex Head 0.312 In, Head Height 0.120 In, Washer Od 0.414 In, Drill Point Size #3, Drill Point Length 0.300 In, For Attaching Variety Of Materials To Metal, Meets/exceeds Sae J78, Package 100 Minimize

80/20 Inc 10 Series 2 Hole Access Hole Drill Jig for #1020 ... Read more

80/20 Inc 10 Series 2 Hole Access Hole Drill Jig for #1020 T-Slot Aluminum Extrusion, Part #6131. This is NEW INVENTORY from the factory and includes the mounting hardware. (The extrusion is not included.) Measures 1" x 2" x .50" thick Mounts into the T-slots of the 1020 extrusion Locates access holes precisely Hardened dowel pins prevent rotation Replaceable, hardened drill bushings Locator lines for accurate hole location Made of clear anodized 6061-T6 aluminum Condition: New For detailed information on this item or other 80/20 Fractional Extrusions and Accessories, simply click on one of the underlined links below: Profiles & Extrusions Structural Shapes Fasteners Joining Plates Dynamic Pivots Panels & Doors Accessories Floor to Frame Linear Motion Stanchions Tools DIY Machining Minimize

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex ... Read more

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex Washer Head, Case-hardened Steel, Zinc Finish, Size #12, Length 1 1/2 In, Width Of Hex Head 0.312 In, Head Height 0.155 In, Washer Od 0.432 In, Drill Point Size #3, Drill Point Length 0.353 In, For Attaching Variety Of Materials To Metal, Meets/exceeds Sae J78, Package 100 Minimize

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex ... Read more

Self Drilling Screw, Sheet Metal With Neoprene Washer, Hex Washer Head, Case-hardened Steel, Zinc Finish, Size #14, Length 1 1/4 In, Width Of Hex Head 0.375 In, Head Height 0.190 In, Washer Od 0.520 In, Drill Point Size #3, Drill Point Length 0.393 In, For Attaching Variety Of Materials To Metal, Meets/exceeds Sae J78, Package 100 Minimize