> Building Supplies > CRL > Hand and Power Tools

CRL White 888 Premium Grade Caulking Compound CRL 888 Premi ... Read more

CRL White 888 Premium Grade Caulking Compound CRL 888 Premium Grade Caulking is a general purpose butyl-based sealant suitable for use in joints where economical, maintenance-free, and watertight seals are required. Multi-Functional, All Weather Caulk Economical, Air and Watertight Seal Non-Stringy and Easy to Apply and Tool Sealant Estimator Chart Basic Uses CRL 888 is designed for use in joints measuring 3/8" (9.5 mm) or less in metal, glass, wood, plastic, and concrete. This sealing compound is easy to apply with standard manual caulking guns. CRL 888 Premium Grade Caulking is non-stringy during application, and contains no asbestos minerals. When fully cured it forms an elastic, all-weather resistant seal which bonds to many surfaces. Application temperature range is 40° to 120°F (4° to 49°C). It also withstands temperature changes from -20° to 200°F (-29° to 93°C). It is recommended for caulking exterior and interior construction units, under thresholds and aluminum siding, between metal building panels Minimize

Nonflammable, VOC Compliant Easy to Spread Easy to Clean Up ... Read more

Nonflammable, VOC Compliant Easy to Spread Easy to Clean Up No Bracing Required DAP Weldwood Construction/FRP Adhesive is a nonflammable, freeze/thaw stable, trowel grade, acrylic latex-based adhesive with good initial tack and easy spreading characteristics for rapid installation of most FRP (Fiberglass Reinforced Plastic) panels. Designed for interior installing FRP panels to concrete, plaster, plywood, and gypsum wallboard. Water resistant when dry. Produces low odor and is VOC compliant. With V-notched trowel (3/32" x 3/32" x 3/32") approximate coverage is 50-70 sq. ft./gallon.Important NotesRead Technical Bulletin (Spec Data) for proper application procedures and physical and chemical characteristics. See product label or Material Safety Date Sheet (MSDS) for safety information. Minimize

For Narrow, Medium or Wide Stile Aluminum, Wood or Hollow M ... Read more

For Narrow, Medium or Wide Stile Aluminum, Wood or Hollow Metal Doors Non Handed Hex Key Dogging S-Strike for Added Security Made in the USA The CRL Jackson 1295 is designed for use with narrow stile aluminum, hollow metal or wood single doors, or paired doors when used with the 896 removable mullion. Sized for 48" openings, but may be trimmed for narrower conditions. Uses the standard C-type strike. Minimize

C.R. LAURENCE 3010 CRL Wireless Picture Hanger Display 10 C ... Read more

C.R. LAURENCE 3010 CRL Wireless Picture Hanger Display 10 Cards. CRL"s Wireless Hangers are designed to allow secure hanging of the heaviest mirrors or pictures. The leveling process is easily accomplished after installation with a Phillips screwdriver. Each card includes one pair of hangers and nails for wall mounting.. Part Numbers Variations: 3010 Minimize

Designed for Use with Narrow, Medium or Wide Stile Aluminum ... Read more

Designed for Use with Narrow, Medium or Wide Stile Aluminum, Wood or Hollow Metal Doors Fluted Texture Extrusion Hex Key Dogging Non-Handed Field Sizable to 30" The sleek, contemporary CRL Jackson 1295 Series Rim Panic Exit Device is designed for use with narrow stile aluminum, hollow metal or wood single doors, or paired doors when used with the 896 removable mullion. Sized for 36" standard openings, but may be trimmed for narrower conditions. Minimize

Smooth Creamy Consistency Paintable Ready to Use for Wood a ... Read more

Smooth Creamy Consistency Paintable Ready to Use for Wood and Metal Sash CRL Dap '33' Glazing Compound is smooth and flexible, and comes ready to use for face glazing wood and metal window frames. Its adhesion to both glass and sash is excellent, and forms a dependable air-and watertight seal that resists sagging, shrinking, chalking and cracking. Color: White Size: 1 qt (32 fl oz) (946 ml) Surfaces should be clean, dry and free of frost. Wood sash that is not primed or painted must be primed first with an oil based primer and allowed to dry. When re-glazing, remove all old putty and bedding by using the following tools: 4500, PR9000, AK40. If any separation has occurred in glazing, mix entire contents of container until uniform. Do not thin glazing. If necessary, place glazing in hands and roll in to coils to warm and soften. Smooth glazing to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is one to two weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint, or if using a latex paint, prime first with a high quality oil based primer. Available in five container sizes. Important Note: Do not thin glazing. Do not apply when air or sash temperatures are below 40 degrees F (4 degrees C). Do not use on plastic windowpanes, insulating glass units with an organic seal, any windowpane over 48 inches (1,219 millimeters) in length, or metal sash with rabbets over 1-1/4 inch (32 millimeters) wide. Also not recommended for stained/leaded glass projects. Clean tools immediately after use with mineral spirits. Be sure container lid is closed and tightly sealed. Store in a cool, dry place. Check can label and Specification Data Sheet for additional limitations. Minimize

Snaps into Locking Position Zinc Plating Prevents Rust The ... Read more

Snaps into Locking Position Zinc Plating Prevents Rust The CRL Shelf Support for KV233 Standards are designed to provide the flexibility needed for different shelf sizes and glass thicknesses. Simply place the Shelf Support in the desired shelf location and snap into place. To change the shelf location, remove the support and place in the new slot. A rubber mallet may needed to remove the support once installed in the standard. Minimize

C.R. LAURENCE SW250W17 CRL White Self-Adhesive Weatherstrip ... Read more

C.R. LAURENCE SW250W17 CRL White Self-Adhesive Weatherstrip - 17". CRL Self-Adhesive Weatherstrip is designed to be applied to the "stop" perimeter of a frame to prevent energy loss, reduce noise and dust infiltration. It will not crack or craze in cold or heat. Self-adhesive application makes installation easy and requires only scissors or a utility knife to cut to size. Tested in accordance with ASTM E-283 and listed by Warnock Hersey for use on labeled openings up to 90 minutes.. Minimize

Can Be Adjusted to Level After Installation CRL's Wireless ... Read more

Can Be Adjusted to Level After Installation CRL's Wireless Hangers are designed to allow secure hanging of the heaviest mirrors or pictures. The leveling process is easily accomplished after installation with a Phillips screwdriver. Each card includes one pair of hangers and nails for wall mounting. Minimum Order: 1 package (1 pair of hangers, nails for wall mount) Minimize

High Quality Formulation for Face Glazing of Wood Sash Stur ... Read more

High Quality Formulation for Face Glazing of Wood Sash Sturdy Plastic Pails CRL Wood Sash Putty is formulated for primerless application to wood. It goes on smooth and evenly, and its off-white color blends with most unfinished wood surfaces. Color: Off-White Size: 1/2 pt (237 ml) Minimum Order: 1 HP Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding; using a 4500, PR9000 or AK40. If necessary, place glazing in hands and roll in to coils to warm and soften. Smooth glazing to an angle that sheets water with a putty knife using a 2BE118, 4701 or 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint. TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797. CRL Wood Sash Putty is long lasting, and factory sealed for freshness. Minimize

The Popular Choice of Professionals Glazes Wood, Metal and ... Read more

The Popular Choice of Professionals Glazes Wood, Metal and Aluminum Sash Ideal for Over-The-Counter Sales Use our CRL All Purpose Putty in most any glazing application to wood, steel and aluminum sash. Its special formulation adheres firmly to sash and glass, and outlasts ordinary putties. Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding using; 4500, PR9000, AK40. If necessary, place glazing in hands and roll in to coils to warm and soften. Smooth glazing to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint.TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797.Both gray and white colors come in factory sealed plastic containers that preserve freshness and shelf life. Attractively labeled for over-the-counter retail sales, in your choice of five sizes.Do not thin glazing. Check can label and Specification Data Sheet for additional limitations. Minimize

Snaps into Locking Position Zinc Plating Prevents Rust The ... Read more

Snaps into Locking Position Zinc Plating Prevents Rust The CRL Shelf Support for KV233 Standards are designed to provide the flexibility needed for different shelf sizes and glass thicknesses. Simply place the Shelf Support in the desired shelf location and snap into place. To change the shelf location, remove the support and place in the new slot. A rubber mallet may needed to remove the support once installed in the standard. Minimize

Use for Steel, Aluminum or Galvanized Window Sash Sturdy Pl ... Read more

Use for Steel, Aluminum or Galvanized Window Sash Sturdy Plastic Pails Made expressly for glazing in steel, aluminum or galvanized window sash, CRL Metal Sash Putty is made to apply smoothly, without priming. The gray color blends with the metal finish. Color: Gray Size: 1 qt (32 fl oz) (946 ml) Minimum Order: 1 Quart Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding using; 4500, PR9000, AK40. If necessary, place putty in hands and roll in to coils to warm and soften. Smooth to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint. TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797. Minimize

The Popular Choice of Professionals Glazes Wood, Metal and ... Read more

The Popular Choice of Professionals Glazes Wood, Metal and Aluminum Sash Ideal for Over-The-Counter Sales Use our CRL All Purpose Putty in most any glazing application to wood, steel and aluminum sash. Its special formulation adheres firmly to sash and glass, and outlasts ordinary putties. Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding using; 4500, PR9000, AK40. If necessary, place glazing in hands and roll in to coils to warm and soften. Smooth glazing to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint.TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797.Both gray and white colors come in factory sealed plastic containers that preserve freshness and shelf life. Attractively labeled for over-the-counter retail sales, in your choice of five sizes.Do not thin glazing. Check can label and Specification Data Sheet for additional limitations. Minimize

High Quality Formulation for Face Glazing of Wood Sash Stur ... Read more

High Quality Formulation for Face Glazing of Wood Sash Sturdy Plastic Pails CRL Wood Sash Putty is formulated for primerless application to wood. It goes on smooth and evenly, and its off-white color blends with most unfinished wood surfaces. Color: Off-White Size: 1 qt (946 ml) Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding; using a 4500, PR9000 or AK40. If necessary, place glazing in hands and roll in to coils to warm and soften. Smooth glazing to an angle that sheets water with a putty knife using a 2BE118, 4701 or 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint. TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797. CRL Wood Sash Putty is long lasting, and factory sealed for freshness. Minimize

Snaps into Locking Position Zinc Plating Prevents Rust The ... Read more

Snaps into Locking Position Zinc Plating Prevents Rust The CRL Shelf Support for KV233 Standards are designed to provide the flexibility needed for different shelf sizes and glass thicknesses. Simply place the Shelf Support in the desired shelf location and snap into place. To change the shelf location, remove the support and place in the new slot. A rubber mallet may needed to remove the support once installed in the standard. Minimize

Snaps into Locking Position Zinc Plating Prevents Rust The ... Read more

Snaps into Locking Position Zinc Plating Prevents Rust The CRL Shelf Support for KV233 Standards are designed to provide the flexibility needed for different shelf sizes and glass thicknesses. Simply place the Shelf Support in the desired shelf location and snap into place. To change the shelf location, remove the support and place in the new slot. A rubber mallet may needed to remove the support once installed in the standard. Minimize

One-Part Smooth Finish Formula with Primerless Adhesion on ... Read more

One-Part Smooth Finish Formula with Primerless Adhesion on Most Common Construction Surfaces +100% to -50% Joint Movement Capability CRL M64 Polyurethane is a high performance, low modulus, one-component, moisture curing modified polyurethane sealant. It has a smooth, even consistency and surface when cured. M64 requires no priming for common substrates such as brick, concrete, aluminum, wood and granite. It applies with any standard cartridge caulking gun to clean, dry surfaces. M64 was specifically developed for sealing dynamically moving joints, such as: expansion and control joints, precast concrete panel joints, curtainwall joints, perimeter caulking (masonry, windows, doors, panels), bedding of mullions, panels and frames. It is compatible with I.G. sealants when glazing units and applied as a toe or heel bead. M64 exhibits tenacious adhesion which will not dissipate with time. This unique weather-resistant formulation possesses a balanced adhesive strength, low modulus and high recovery, making it ideal to withstand the following adverse conditions common to such installations: moisture, movement, shear and deflection. M64 is suitable for continual immersion in water with the use of the appropriate primer. Paintable after full cure, minimum 72 hours. In order to help you better select the correct sealant, we have put together a Silicone and Sealant Selector Chart . Color: PermaWhite Contents of Cartridge: 10.1 fl oz (300 ml) Minimum Order: 1 Each Technical Data : Conforms to U.S. Federal Specification TT-S-00230C, Type II, Class A; ASTM C920-98, Type S, Grade NS, Class 25, Use NT, M, T, A, and O. CAN/CGSB 19, 13-M87, Type MCG-225-A-N with QPL #81050. USDA Approved Comparable Sealants : CRL M66 Polyurethane; Tremco Vulkem 921, Tremco Vulkem 116, Tremco Vulkem 911, Tremco Vulkem 931, Tremco DyMonic; Sika 1A, Sika 15LM; Sonneborn NP1, Sonneborn Sonolastic 150; Pecora Dynatrol 1; Minimize

Strong, Flexible, and Durable Adheres to Most Surfaces Low ... Read more

Strong, Flexible, and Durable Adheres to Most Surfaces Low VOC Formulation Paintable Part of a Complete Moisture Control System CRL Moistop® Sealant is a quality polyurethane sealant that is designed to be compatible with wood, vinyl and aluminum flanges, Jumbo Tex® building paper, WeatherSmart®, FortiWrap®, PlyDry® and all Fortifiber flashings. It is the most logical choice for window and door installations and a variety of other building applications. CRL Moistop® Sealant delivers excellent adhesion, compatibility, durability and moisture resistance to prevent water leaks and the expensive callbacks they cause. Minimum order is one each cartridge. Contents : 10.1 Fl. Oz. Exceeding ASTM C-920 and AAMA 808.3-92 (Exterior Perimeter Sealing Compounds) standards, Moistop Sealant makes it easy to get extraordinary results from an ordinary caulking gun. A continuous bead on the window nail flange gives long lasting protection against moisture infiltration. Minimize

The Popular Choice of Professionals Glazes Wood, Metal and ... Read more

The Popular Choice of Professionals Glazes Wood, Metal and Aluminum Sash Ideal for Over-The-Counter Sales Use our CRL All Purpose Putty in most any glazing application to wood, steel and aluminum sash. Its special formulation adheres firmly to sash and glass, and outlasts ordinary putties. Color: Gray Size: 1/2 pt (8 fl oz) (237 ml) Minimum Order: 1 HP Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding using; 4500, PR9000, AK40. If necessary, place glazing in hands and roll in to coils to warm and soften. Smooth glazing to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint. TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797. Both gray and white colors come in factory sealed plastic containers that preserve freshness and shelf life. Minimize

High Quality Formulation for Face Glazing of Wood Sash Stur ... Read more

High Quality Formulation for Face Glazing of Wood Sash Sturdy Plastic Pails Attractively Labeled for Resale CRL Wood Sash Putty is formulated for primerless application to wood. It goes on smooth and evenly, and its off-white color blends with most unfinished wood surfaces. Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding; using a 4500, PR9000 or AK40. If necessary, place glazing in hands and roll in to coils to warm and soften. Smooth glazing to an angle that sheets water with a putty knife using a 2BE118, 4701 or 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint.TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797.It comes in sturdy plastic pails that are attractively labeled for retail sales. CRL Wood Sash Putty is long lasting, and factory sealed for freshness.Do not thin glazing. Check can label and Specification Data Sheet for additional limitations. Minimize

Snaps into Locking Position Zinc Plating Prevents Rust The ... Read more

Snaps into Locking Position Zinc Plating Prevents Rust The CRL Shelf Support for KV233 Standards are designed to provide the flexibility needed for different shelf sizes and glass thicknesses. Simply place the Shelf Support in the desired shelf location and snap into place. To change the shelf location, remove the support and place in the new slot. A rubber mallet may needed to remove the support once installed in the standard. Minimize

One-Part Smooth Finish Formula with Primerless Adhesion on ... Read more

One-Part Smooth Finish Formula with Primerless Adhesion on Most Common Construction Surfaces +100% to -50% Joint Movement Capability CRL M64 Polyurethane is a high performance, low modulus, one-component, moisture curing modified polyurethane sealant. It has a smooth, even consistency and surface when cured. M64 requires no priming for common substrates such as brick, concrete, aluminum, wood and granite. It applies with any standard cartridge caulking gun to clean, dry surfaces. M64 was specifically developed for sealing dynamically moving joints, such as: expansion and control joints, precast concrete panel joints, curtainwall joints, perimeter caulking (masonry, windows, doors, panels), bedding of mullions, panels and frames. It is compatible with I.G. sealants when glazing units and applied as a toe or heel bead. M64 exhibits tenacious adhesion which will not dissipate with time. This unique weather-resistant formulation possesses a balanced adhesive strength, low modulus and high recovery, making it ideal to withstand the following adverse conditions common to such installations: moisture, movement, shear and deflection. M64 is suitable for continual immersion in water with the use of the appropriate primer. Paintable after full cure, minimum 72 hours. In order to help you better select the correct sealant, we have put together a Silicone and Sealant Selector Chart . Color: Tan Contents of Cartridge: 10.1 fl oz (300 ml) Minimum Order: 1 Each Technical Data : Conforms to U.S. Federal Specification TT-S-00230C, Type II, Class A; ASTM C920-98, Type S, Grade NS, Class 25, Use NT, M, T, A, and O. CAN/CGSB 19, 13-M87, Type MCG-225-A-N with QPL #81050. USDA Approved Comparable Sealants : CRL M66 Polyurethane; Tremco Vulkem 921, Tremco Vulkem 116, Tremco Vulkem 911, Tremco Vulkem 931, Tremco DyMonic; Sika 1A, Sika 15LM; Sonneborn NP1, Sonneborn Sonolastic 150; Pecora Dynatrol 1; OSI Minimize

One-Part Smooth Finish Formula with Primerless Adhesion on ... Read more

One-Part Smooth Finish Formula with Primerless Adhesion on Most Common Construction Surfaces +100% to -50% Joint Movement Capability CRL M64 Polyurethane is a high performance, low modulus, one-component, moisture curing modified polyurethane sealant. It has a smooth, even consistency and surface when cured. M64 requires no priming for common substrates such as brick, concrete, aluminum, wood and granite. It applies with any standard cartridge caulking gun to clean, dry surfaces. M64 was specifically developed for sealing dynamically moving joints, such as: expansion and control joints, precast concrete panel joints, curtainwall joints, perimeter caulking (masonry, windows, doors, panels), bedding of mullions, panels and frames. It is compatible with I.G. sealants when glazing units and applied as a toe or heel bead. M64 exhibits tenacious adhesion which will not dissipate with time. This unique weather-resistant formulation possesses a balanced adhesive strength, low modulus and high recovery, making it ideal to withstand the following adverse conditions common to such installations: moisture, movement, shear and deflection. M64 is suitable for continual immersion in water with the use of the appropriate primer. Paintable after full cure, minimum 72 hours. In order to help you better select the correct sealant, we have put together a Silicone and Sealant Selector Chart . Color: Limestone Contents of Cartridge: 10.1 fl oz (300 ml) Minimum Order: 1 Each Technical Data : Conforms to U.S. Federal Specification TT-S-00230C, Type II, Class A; ASTM C920-98, Type S, Grade NS, Class 25, Use NT, M, T, A, and O. CAN/CGSB 19, 13-M87, Type MCG-225-A-N with QPL #81050. USDA Approved Comparable Sealants : CRL M66 Polyurethane; Tremco Vulkem 921, Tremco Vulkem 116, Tremco Vulkem 911, Tremco Vulkem 931, Tremco DyMonic; Sika 1A, Sika 15LM; Sonneborn NP1, Sonneborn Sonolastic 150; Pecora Dynatrol 1; OSI Minimize

Snaps into Locking Position Zinc Plating Prevents Rust The ... Read more

Snaps into Locking Position Zinc Plating Prevents Rust The CRL Shelf Support for KV233 Standards are designed to provide the flexibility needed for different shelf sizes and glass thicknesses. Simply place the Shelf Support in the desired shelf location and snap into place. To change the shelf location, remove the support and place in the new slot. A rubber mallet may needed to remove the support once installed in the standard. Minimize

Use for Steel, Aluminum or Galvanized Window Sash Sturdy Pl ... Read more

Use for Steel, Aluminum or Galvanized Window Sash Sturdy Plastic Pails Made expressly for glazing in steel, aluminum or galvanized window sash, CRL Metal Sash Putty is made to apply smoothly, without priming. The gray color blends with the metal finish. Color: Gray Size: 1/2 pt (8 fl oz) (237 ml) Minimum Order: 1 HP Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding using; 4500, PR9000, AK40. If necessary, place putty in hands and roll in to coils to warm and soften. Smooth to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint. TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797. Minimize

The Popular Choice of Professionals Glazes Wood, Metal and ... Read more

The Popular Choice of Professionals Glazes Wood, Metal and Aluminum Sash Ideal for Over-The-Counter Sales Use our CRL All Purpose Putty in most any glazing application to wood, steel and aluminum sash. Its special formulation adheres firmly to sash and glass, and outlasts ordinary putties. Color: White Size: 1/2 pt (8 fl oz) (237 ml) Minimum Order: 1 HP Surfaces should be clean, dry and free of frost. When re-glazing, remove all old putty and bedding using; 4500, PR9000, AK40. If necessary, place glazing in hands and roll in to coils to warm and soften. Smooth glazing to an angle that sheets water with a putty knife; 2BE118, 4701, 2S114. Typical dry time before painting is four to six weeks depending on temperature and humidity. Putty must be painted after it has skinned over and attained a firm set. For best results, use a high quality oil-based paint. TECHNICAL DATA: Meets the requirements of Federal Specification TT-G-410E; ASTM C 669-75, C669, D2249, D2376, C797. Both gray and white colors come in factory sealed plastic containers that preserve freshness and shelf life. Minimize